This shock absorber kit is an authentic OEM part that is sourced directly from the manufacturer. The kit includes two dual-stage shock absorbers, one spare shock mounting pin, and four locking nuts. T...
$39.67
In Stock
Order within the next 3 hrs and your part ships today!
The water inlet valve has two ports for water to enter and controls the flow of water into a washing machine. Hot, cold, and warm water can easily enter the washer this way. If the water inlet valve i...
$127.65
In Stock
Order within the next 3 hrs and your part ships today!
This is a single spring with insulator, but you may also know it as a suspension spring. It is a part for your washing machine. If your tub is no longer stable, which would cause shaking, moving, and ...
$47.69
In Stock
Order within the next 3 hrs and your part ships today!
This drain hose is designed for use in your washer. The function of this part is to carry water from the drain pump to the house drain. If your washer is leaking or will not drain, you may need to rep...
$20.58
In Stock
Order within the next 3 hrs and your part ships today!
This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. T...
$11.21
In Stock
Order within the next 3 hrs and your part ships today!
This is a drive belt for your washing machine. This part spins the basket in your appliance by connecting the drive motor to the drive system. You will need to replace the drive belt if your pumps are...
$13.31
In Stock
Order within the next 3 hrs and your part ships today!
First, I had to remove 2 screws to take off the 2 broken pieces of the door catch. Then I put the new one on using the same 2 screws. The door is now able to close, but does not lock properly. In order to make it work, I put a thin piece of rubber into the place where the door meets the machine. This causes the lock to engage and the
... Read moremachine to work. I don't know how much longer it will work since the repairman claims that the main bearing is going, but hopefully it will last a bit longer.
Part Select got the part to me in one day using the standard shipping, which was impressive. I just wish that I hadn't wasted money on calling a repairman only to have him tell me that he didn't have the part. He charged for the visit anyway even though I told him ahead of time the problem and the model of my machine.
removed 2 screws and removed top access cover. removed 2 screws and removed front access cover. removed 4 retaining pins (one with nammer and punch because it was stuck) connected lower ends of new shocks with plastic pins, extended each shock to slip fit and connected upper ends to wash tub mounts. Reinstalled panels. I wish I could sa
... Read morey that it all went well from there but......when the shocks broke, apparently the hit the motor took was enough to cause an electronic failure of the speed cycle control chip. Now Im waiting for that part.
Turned out drum brackets were corroded, so drum and shell-rear/brg and gasket needed replacing
1. Disconnect power and water lines 2. Remove rear and top panels 3. Remove control knobs, Assembly, soap dispenser, and Assembly cons frame/trim 4. Remove all screws from control panel mounting bracket (panel-cont
... Read moremtg wing bend), disconnect easy wires to get to so you can flip it on it's edge when the time comes - no need to remove completely 5. Disconnect hoses running to shell-rear/brg 6. Remove the motor (motor-Sole) and belt 7. Place foam pad and/or jack with pad on it underneath shell (it's gonna be very heavy when you remove it - two men or a jack required) 8. Lift and remove the two spring/sleeves that support the shell. 9. Remove two level-shocks below shell or at a minimum remove one of the pins on each 10. Remove Spring boot from bellow 11. Lower and remove entire shell 12. Remove the weight, upper back from the rear shell and the counterweights from the front shell (can leave front weights if you want to, but probably easier to work with without them on. Note: be careful, these all crack/chip very easily) 13. Remove the screws that hold the rear shell to the front shell 14. Remove the pulley screw and pulley (may take a little wiggling or tapping with rubber mallet to loosen) 15. Separate the rear shell from front shell. 16. Remove the drum from the rear shell (may also require some wiggkling/tapping with rubber mallet)
Note: I did this from memory, so probably missed some steps - just use your parts manual to ensure you know what you're looking at and it will help you through the process.
Good luck. I figure I saved about $700 to $1200 since the estimated repair costs were so high, I would have simply had to buy a new washer.