ZISW42DCB General Electric Refrigerator - Instructions

Removed icemaker from freezer,
Removed 3 screws from cover plate, and removed screw securing main gear, removed gear.
Pulled back cover plate to expose switches and mechanism.
Removed screw holding switch to remove switch, and installed new switch.
I should have taken a pic of the cover plate, the interior mechanism and the wiring as I went along. It would have saved me 45 minutes in reassembly. Also, as luck would have it, I reversed the wiring on the switch. So off was on, and I had to remove it, switch wires and re-install.
But it works!

the previous left behind a side by side, everything worked however the auger in the ice bucket was a little rusty. I wish that I could say it was all me but the truth of the matter was the videos on file.

They were nicely done and easy to follow as I took the unit apart and replaced the auger in about 30 minutes. Thanks for all your help in part look up.

Part attaches to metal plate near crushing fingers which attaches to ice holding bin. Remove about 6 screws total on each side of plate. You must disassemble the auger & other parts so you can reassemble it in the proper order. Not many parts but i always take pics to cut down on time. New part is at the other end of the auger and acts as the holde of the auger shaft. Picture a crankshaft with a bearing on each end so the auger rotates between new part and the other end of auger shaft. That's it.

Since I really needed to replace the deteriating auger I used the original ice bucket and transferred the new auger assembly into the old ice bucket. Looked complicated at first, but make it work and my refrigerator is now making nice clean ice. It would have taken a lot longer if I sent the new bigger ice bucket back and it was my fault. With the videos and pictures on line made the replacement of the auger & ice bucket easy. Thanks Bill

removed the bulb from the package unscrewed the old bulb & screwed in the new bulb.

I simply removed 6 screws that held bucket to face and pit on new bucket and put it back in freezer works great

Followed the online video. Unplugged refrigerator, removed trim piece, lifted control board cover, removed 4 screws retaining circuit control board and removed the 3 connectors from the control board. Located flapper and removed by using small flat tip to take tension off flapper connectors. Helper held flash light to illuminate flapper connectors. Reversed procedure. New flapper seals well and cured problems. Circuit board was a bit different than one in video, but still had the 3 connectors. Marked each connector with grease pencil at top edge to ensure correct reconnection. Should note how wires are threaded around circuit board to ensure they are tucked back in correctly in reassembly. Remove trim piece carefully. I broke 2 of the 8 plastic pins that hold trim on. May be due to age of unit as they were brittle. 6 pins still hold trim piece flush.

Replaced dispenser door flapper by following the do it yourself video in this site. It was really easy. Just be careful when removing the dispenser black bezel. I broke one of the little tabs when taking it off.

Researched on internet/you tube; ordered part, and did the repair. Easy to do and saved the cost of a service call.

Remove the one screw holding the unit in place, unplug it, slide in the replacement, plug and screw it in.

1) Shut off water supply
2) Pull out Refrigerator
3) Unplug
4) Unscrew back panel
5) Remove main water supply line
6) Remove bracket
7) Cut supply hoses 1 at a time and insert in new assembly in correponding openings
8) Reverse steps and enjoy

Notes: Judging by the new part's look, I suspect this repair will be needed again in about the same amount of time (5 years). The incoming pressure (I live in NYC) is probably too much for the way the part is built. Fortunately, now I know where to look , what to order and where to get it (great service, partselect.com!) it's no more then a 15 minute job.

My husband took out the old icemaker in about 5 minutes. The new icemaker was a perfect fit even though the refrigerator was >10yrs old. The only difficult part was the plug extension that was needed so that it would fit into an older appliance. The part was included, it just made the cord about 3 inches longer than it needed to. After working with it for about 20 minutes we were able to fit it on the back side of the icemaker. Now it works great!!

Watched you tube video a few times,very helpful.A word of advice take a good,look at the part you are replacing before ordering,dont go by model #,I ordered according to the model and that part did not fit. You also need a 5/16 snap on union for one of the cracked lines,ordered it from GE worked fine.

Use small putty knife to cut internal sealant on ice maker door trim piece. Then you can easily remove it.

Replaced flapper. Followed the video. The lamp caused the removable plastic bracket (which supports the control panel and the ice chute) to fuse with the plastic frame in the door. Eventually broke the fused plastic, removed the bracket, and filed the rough broken plastic before reassembly.