SF337PEXW0 Whirlpool Range - Instructions

took 2 screws out of bottom plate in the oven and lifted it out. removed 2 screw on the flame deflector and took it out. Took 2 screws out of old ignitor and unplugged it. Installed new ignitor tested oven put it back together. took about 30 min. screw driver only

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Had to remove the bottom oven shelf and the broiler drawer. Disconnected the wiring pigtail theought the broiler opening and pulled the gas pipe from the baking oven. Reomved the two screws connecting the ignitor from the pipe. Connected the new ignitor and threaded the wiring pigtail back down the the opening in the baking oven. Connected the wiring harness up inside the broiler and put the drawer back in. Re-installed the bottom shelf in the baking oven and tested. Worked perfectly. Back to cooking. :-)

We removed with a screwdriver the two main screws that held the bottom of the oven in place and removed the bottom oven piece; then we removed the two nuts with a socket wrench that held the element in place. We then discovered that the element wire did not completely egress to the point of being able to disconnect from within the oven, so we removed the storage drawer below the oven and that provided access to disconnect the element wire and reconnect the new element wire and then reverse the steps to install the new element, which worked fine upon first use and continues to work fine.

Oven is gas. Burners on top OK, broiler in oven OK. Removed oven bottom plate and heat deflector. Carborundum igniter would not glow. Ordered new igniter from Partselect.com. With new igniter in hand I unplugged the oven from house power, removed the bottom drawer for access to the igniter connector, and disconnected it. Removed the bad igniter and replaced with new igniter...easy! Plugged in oven to house power and tested new igniter by turning on oven. GOOD!! Reassemmbled oven interior. Wife again happy.

Only replaced a knob. Pulled the old one off and put the knew one on.

Called repair man and described the problem. He said I could do it myself. PartSelect had the part and a previous description on the PartSelect site told me how to do the repair. It was easy. Be careful when removing the igniter nuts. I used a very small amount of sewing machine oil so as not to strip the threads. works great.

This model does not have a removable bottom drawer making access a bit of a challenge.
1. Remove power to the range.
2. Remove the oven door and the kick panel below.
3. Remove the floor of the oven.
4. Remove the burner shield.
5. Become a contortionist, then stick your head and torso in the gas oven.
6. Look at the top in the back to see how the broiler igniter is mounted. Use this to select the proper size wrench. I suggest using little ignition wrenches. The oven igniter is mounted in the same manner.
7. Locate the oven igniter at the bottom, in the back, at the center. Remove the small screw taking care that you do NOT drop the wrench or the screw. This will be done by feel as the screw is only visible after you remove it.
8. Route the wire of the new igniter down, next to the old igniter wire.
9. Crawl under the oven (behind the kick panel you removed, and cut the wire.
11. While you are under there, strip the insulation back on the wires about 3/8 inch. Splice the new igniter wire to the oven using the new wire nut. Check that it is secure.
12. Back to the oven. If your back is still holding up, remove the old igniter. Install the new igniter and the old screw. Tighten securely, taking care to not strip the threads.
13. Remove all of your tools, your head, and your torso.
14. Plug the oven back in temporarily, turn the oven on and verify the igniter heats up.
15. Unplug the range again.
16. Reinstall the burner shield, the oven bottom, the door and the kick panel.
17. Make sure you have all of your tools, stand up, and since you are now a contortionist, pat yourself on the back!

this was so simple.. attach with 2 screws and plug in and done.. less than a minute.. to be honest it took me longer to put the oven back together than installing the new part. lol

ordered new broiler pan

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

very easy

Screwed in light bulb and glass protector