All Installation Instructions for Hotpoint Range RGB790SEH3SA

The eye would not light

Remove the existing burner and install the replacement.

Parts Used:

Burner Head - Large - 12K

Solomon A from COLLEGE PARK, GA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Uneven flame on large gas burner

The part was very easy to switch out but it made no difference whatsoever so I returned it. The way it is designed is the problem. There is a pie slice shaped gap on the burner which causes a gap of no flame. Also a C shaped cut out around the igniter which causes another no flame gap.

Parts Used:

Burner Head - Large - 12K

Drawer Glider - Left Side

Drawer Glider - Right Side

Chris from BAILEY, CO
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Broken button behind overlay

Remove both over and control panel and replace both

Parts Used:

OVERLAY T09-B HP (Black)

Frederick from MAYSVILLE, NC
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Removal reinstalling

Removal old fashioned oven door handle took time after removing the oven door. New replacement handle was easy to install! Try to reinstall was long and finally got installed after 5 attempts due hinge on right side issue

Parts Used:

Door Handle

Thomas from HAMPSTEAD, NH
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Screw drivers, Socket set

1 person found this instruction helpful.

Was this instruction helpful to you?

some of electrodes not working at times,found were bad,wires had some insulation missing, clips looked burnt,found all new parts replaced

the electrodes on this model have to be removed before you can raise cooktop, once cooktop is raised remove wire from burner bracket, use needle nose pliers to squeeze bottom of clip,remove &replace with new parts.

Parts Used:

Top Electrode Mounting Clip

Dana from LEEDS, AL
Difficulty Level:
Really Easy
Total Repair Time:
More than 2 hours
Tools:
Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

BASE OF BULB BROKE OFF & WELDED TO SOCKET

PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.

Parts Used:

RECEPTACLE PUSH-IN

NEIL from ROCKY POINT, NY
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

Oven bottom badly marred after 16 years.

Two set screws in rear; removed easily with a screwdriver. Old oven floor lifted out easily; new oven floor dropped in just as easily; set screws re-installed. Done. Pleasantly surprised at how easy this went.

Parts Used:

BOTTOM OVEN AND DEFLECTOR ASM

Charlie from NAPLES, FL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

finish on old oven bottom was damaged

Ordered part from customer friendly Part Select and received the replacement part within a few days, and installed it promptly. Wife is happy and stopped grumbling about oven bottom unsightly defect! Small price to pay for a happy wife! Ernie

Parts Used:

BOTTOM OVEN AND DEFLECTOR ASM

ERNEST from MANCHESTER, NJ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

oven racks old and ugly

1. Open oven door
2. insert oven racks (perfect fit)
3. close oven door. Done and finished - man am I tired

Parts Used:

Oven Rack

Claudene from ORCUTT, CA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

The old burners were damaged by the prior owners.

The repair was extremely easy. Just removed the old burners and dropped in the new ones. No tools needed.

Parts Used:

Burner Head - Medium - 9500

Burner Head - Large - 12K

Mohammad from BARTLETT, IL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Burners wouldn't light

Had two burners on the stove that would not light. Had tried cleaning them but they still did not ignite. Replaced both burner heads. Once replaced. they ignited right away and have worked ever since.

Parts Used:

Burner Head - Large - 12K

Burner Head - Medium - 9500

Robert from SOUTH ELGIN, IL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

The light inside the oven had burned out

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Parts Used:

Light Bulb - 40W

Catherine from SEATTLE, WA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

3 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Lightning strike. Ignitors on stove work but display for oven was blank

Remove rear cover. Remove old display. Remove one wire (and place on new board) at a time. Carefully remove faceplate from old board and place on new one. Close everything up and your done. Took 10-15 minutes.

Parts Used: