PLHS69EESS7 Frigidaire Refrigerator - Instructions

pushed release button removed filter, installed new filter

First removed food from the refrigerator door.

Second removed plastic cover plate and metal plate assembly from top of door.

Third lifted door of metal pin on bottom.

Fourth removed broken closer plate and replaced
with new closer plate.

Set door back in place.

Re secured the metal plate and plastic cover plate.

Replaced the door shelves and food. DONE.

Ordered new water filter. It arrived, I opened it and took out the old one and put in the new one. I worked perfectly
as soon as I realized I had to remove the protective caps.

I followed the video tutorial published here. The step I altered was setting the shrink wrap; I did not have a heat gun to safely shrink it, so I folded it tightly onto itself and wrapped it in electrical tape. No more frost buildup.

This is the second time I've had to replace the crisper cover, so I had that step mastered. As before, I took the glass from broken crisper cover and dropped it into new cover in seconds. Had to use a screwdriver to pry old crisper supports from the walls of the fridge. This was the only hassle. Popped new supports in, replaced crisper covers, and slid crisper drawers back into place. From now on, I'll have to be more careful about how much weight I put into crispers.

Could have done it with my eyes closed! Removed shelf and drawer, then removed broken support rail. Removed screw from broken rail and put the new, two piece rail together using that screw. Snapped rail back onto wall...returned shelf to fridge...returned drawer to fridge...returned myself to sanity! Yee Haw Easier than installing it was ORDERING IT. I was amazed by the ease of that process. Your ordering site is incredibly easy. By the way...I am a blonde and for blondes everywhere...Look at what I could do :)

Unscrew 4 screws . Remove broken basket hangers. Install new basketo hangers. Screw in 4 retaining screws...

Removed the plastic water tubes cover with a nut driver. Disconnected water hoses. Dropped control box assembly with nut driver. Removed old filter base with phillips screwdriver. Assembly opposite.

Took off Door on Refr. and unscrewed Doorstop,
removed doorstop with broken Bearing and replaced with new Parts. Took about 20 Minutes
including reattaching Door. A 10 year old can do it.

Consult the exploded view of the Ice Container on this site. A likely cause the end plate (17) is worn. This plate connects the rotating corkscrew to the final plastic worm that pushes the ice into the crusher and thence to your waiting glass. The worm alone will not do the trick. To replace this plate, you need to take out all of the screws you can see, including the one that holds the spring for the crusher select bar.. First, the front cover, then the plate, and finally, locking ring from the worm and the black housing for the crusher. Now you can remove the whole worm assembly. Using a cloth or rubber insulator to protect it, unscrew the end screw and slide off the crusher teeth. Store on the table as a unit to facilitate re-assembly. Slide off the old bar and worm, put them back, and re-assemble. Takes a little dexterity to get the crusher select bar back, but not hard. Easy job.

Noticed the evap fan wasn't working, so trying to disconnect the wire broke the connection so had to order a new motor. Installed the motor but it still didn't work. Had a technician look at it and he said it was the control board. Ordered and installed control board and still didn't work. The only element left is the evap thermostat. Jumped the thermostat and it worked so ordered and installed a thermostat. It works now

Twisted replacement bulb into place easily. Let there be light!

Removed screws holding unit and removed unit. Removed switch from connectors in unit. Replaced unit without switch. On day switch arrived (delivery was prompt) my wife replaced switch by attaching the two connectors and slipping into unit without having to remove entire unit. How easy was that!!!

Took drawers out by removing 2 screws on top of rail near front, then popped black plastic cover off in lower right inside cabinet...sensor just un plugged and new one plugged in easily...did not fix problem though...display set at 34 but bottom drawer reads about 40 at best and upper drawer reads around 55...dont think the 3 little fans inside on back wall have been running

Followed instructions for this part from this site and things went well.