PDW8200J03CC General Electric Dishwasher - Instructions

I watched this video: https://www.youtube.com/watch?v=-k0iZGwMOGc
And then I did exactly what it said! It was easy. Plus, when I opened the panel I could see the old switch interlock assembly was melted on one side, so I knew I had gotten the right part!

I had a shut off water supply shut off shut under my sink. That is where I shut the water off for the dishwasher. I knew it was for the dishwasher ,because it follow the line, and could see it was going to the washer. Then I went down stairs in the basement. Opened my breaker box, and found the breaker for the dish washer marked dish washer, and put in the off position. When I was still up stairs I opened dish washer , and inside at the top was two screws holding the dishwasher to the counter top. Those two screws turned out to be the exact size of just about every screw I ended up having to unscrew on this machine. So at the time I was in the basement turning off breaker, I went to the garage to gather up tools. Take the two screws that are screwed to the counter top. Then I layed on the floor, and at the bottom of the dish washer there is a panel on the front of the machine with screws attaching it. Take those screws out. Pull off cover. Now get a flash light so you can see. They're adjustable feet that the dishwasher are being leveled by. Those feet need to most likely be adjusted down so you can the machine pulled out, and make it possible to work on. now you can you can pull it out, but watch that water supply line does not get hung up, or electrical wires. Once the machine is pulled out there is another cover on the front that I took off. Four screws hold it on. Now you can get to the part to fix it. The other thing you need to know is after taking off the valve and taking off the old 90 fitting. It will need cleaned up. When you put it on the new shut off valve use pipe dope or thread tape so it doesn't leak. Good luck.

Used Phillips screwdriver to undo brackets that keep dishwasher in place. Pulled out dishwasher from underneath the counter. Placed hinge arm in spring, hooked spring onto clip, placed hinge arm in clip. Put back dishwasher under the counter and screwed in place. Took all of 15 minutes. Saved 185.00 for service call.

The entire flat side of the end cap, (with the cutout latch), goes on the outside of the guide bar. It took less than 15 seconds to insert. It took about 30 minutes of searching for videos and playing around with the part to figure this out. A simple diagram would have been helpful.

Followed the instruction video on your website. It was accurate and valid. The repair should have taken 15 mins., instead one of the screws holding the dispenser was frozen. Tried DW-40, and liquid wrench. Neither worked because the screw was in plastic.Finally got out the Dremel and cutting wheels. Had to cut away enough of the unit until I could get at the screw (it was the center bottom one). Sliced through some more of the housing, then cut a notch in the screw head deep enough so I could apply enough pressure with a flat blade screwdriver to open it. After that things went as smoothly as could be expected.A bad design and cheap materials.

Man, if you need help doing this repair, you shouldn't even own a dishwasher, much less a house. This was the easiest repair in the entire galaxy. First, I removed the old wheels, which was easy becasue they were always falling off by themselves. I then had to use pliers to squeeze the old studs to remove them from the wheels. All the wheels were still in good shape. Then I snapped the wheels onto the new studs, and snapped the studs onto the lower rack. And then, it was like I was in heaven. Bluebirds were singing, the sun was shining, my lower rack was sliding in and out and in and out like it was new. O happy day.

This lower rack (GE part #WD28X25960) was ready to roll right into the dishwasher straight out of the box, no tools needed.

Watched the video, and followed the directions. Although my machine had some slight differences, the repair went pretty much per the video. Got all connections back where they belonged, cleaned up the insides a little while had the door parts separated, then buttoned it all back up, ran a cleaning solution thru empty washer, let it dry then started filling with dishes and ran the wash cycle the next day when full. All is well.

Thought it might be check flapper valve on drain pump, so I replaced fairly easily, per instructions. When doing, I noticed the attached relay wires were not secure. When it was on the drain cycle one of the relay wires vibrated badly and loosened the connection enough to only work occasionaly. Would like to put new relay on the pump but they do not sell separately from the pump. (one assembly). I resecured connection and will wait till relay gives out and buy new assembly, but for now it's working perfectly!

shut off water. removed lower panel disconnected power removed supply hose and outlet hose. disconnected electrical plug from valve. Un bolted valve from frame. removed elbow from valve inlet. installed elbow on new valve using Teflon tape. reinstalled valve to frame. connect hoses + electric plug to new valve. turn water on check for leaks. reconnect power. run dish washer check for leaks & popper operation. reinstall lower panel.

Removed the dishwasher to get at the defective parts and removed,than replaced the two check valves and reassemble.

Turned off the power at the main box. Removed the six phillips screws and two bottom hex screws holding the front panel. Removed the two solenoid wires on the old dispenser (Label wire polarity). Removed the eight screws holding the old soap dispensor and took it out. Cleaned the area around the hole. Laid down a bead of silicon caulk around the hole edges. Placed the new dispenser in the hole and replaced the eight screws (do not over tighten). Replaced the two wires on the dispenser solenoid (check polarity). Replaced the front cover (Do not over tighten. Turned on the power and job complete.

Very easy - remove the screws around the inside of the door. 6 screws and 2 plugs to remove the assembly. Just be careful not the strip the sheetmetal screws when putting it back together. No screwguns...

I removed the old rack and saved the flatware container. Then I put the new rack in.

The difference between the old one and the new one is that between a busted grocery cart with one wheel that always wants to return to the parking lot, and a well-trained dog that does exactly what I ask it to. The new rack was worth the $95 I spent to get it.

The new rack came with wheels and axles, so I didn't need to order more.

Very Easy! Lift old arm out and replaced it with the new one.