PDW8200J03CC General Electric Dishwasher - Instructions

See GE web site for repair instructions. Take out screws at top of door. Slide unit out there is a spring on each side of the door just look at the good one for details. Easy fix. About 30 minutes.

Squeeze the new link to the cable hook with pliers while locking the vise grip to the cable for easier handling. Then, using the vise grip on the cable, hook the other end of the link to the dishwasher door hook

Took old basket out and dropped new one in .

1.Shut off the electric! 2.Shut off the water Supply. 3.Removed the two lower front panels(Two bolts each) . 4.The Water supply Solenoid is located far left up front . 5. Unplug power connector clip to the solenoid. 6.remove the two mounting bolts . 7. Use pliers to compress the rubber hose clamp And slide down the hose . 8 some small amount of water maybe in the hose a pan maybe necessary under the solenoid. 9.Gently pull the rubber hose off the nozzle. Complete installation in reverse. May The Force Be With You!

The sump was very clogged with caulk like crud that we think was a chemical reaction from soap that was used the first two years. When I first started troubleshooting, the sump seemed to be the problem, so I replaced that. There was a small hose on the sump that was broken so it made sense to replace it anyhow.

When that didn't help I put the dishwasher into service mode and observed that there just wasn't enough water to spin the sprayer. Therefore it was a water quantity problem, which can be caused by either the Water Inlet Valve or the Flood Switch.

I ordered both the Water Inlet Valve and the Flood Switch, just in case. I replaced the valve first and when that worked I did not install the switch.

Installation was performed with the dishwasher still inserted in the cabinet. If you have big hands, pull the dishwasher out. With sockets and nut drivers, I was able to remove the assembly. After pulling it out enough to clear the dishwasher, I was able to get a screwdriver on the outlet side clamp and a wrench on the inlet side hose.

My old valve had a 90° elbow on it and that was difficult to remove. Installing the elbow on the new valve was just as bad. The valves don't have enough clearance to get a wrench on them to keep them from turning while the elbow is tightened.

TIP: Take a picture of the valve before removing/disconnecting anything. I don't know if the electrical connector can attach either way but I made sure to put it back on exactly the same way it was.

Simple install- just roll it in. Fit perfect. Better design than OEM part. Perfect.

After removing the screws, the front of the dishwasher easily came off. I put 2 screws back in to hold the control panel in place. I did not want that to dangle while replacing the part. The part came off easily after removing the screws. Everything went together easy.

Easiest repair ever. My new rack arrived in three days, opened the box and slid it in. Better quality than the original. Excellent service!

parts were easy to find and the repair was a breeze. Thanks for your help.

I unplugged and removed my dishwasher and followed the instructions extactly repairing the pump and replacing the parts I had just received. I torgued the ring to the specified amount, installed the pump and found the impeller could not turn. I dis-assembled it all again and loosened the ring to allow the impeller to turn, reinstalled it and when I initiated the wash cycle, water began running wildly. Next step, replace motor and pump as the pump motor shaft has gone out

The repair was easy. Removed all the screws from the inside door panel, approx. 11. Watch out for that last screw as there isn't anything else holding the outside panel, inside panel and control panel together other than those screws. I then unplugged the old dispenser backed out another 6 screws and replaced the old dispenser with the new one. Put it all back together within about a half hour.

I connected one end of hose to the drain using a hose clamp and screwdriver then connected the other end to the dishwasher using anouther hose clamp and a screwdriver..

replaced clips that were much better made.

Removed the existing stud rollers with the wheels attached. Then removed the wheels from the stud roller. Then snapped the wheels on the new "Better Designed" stud rollers. Then easily snapped the new stud roller assembly in place. Piece of cake...works like a charm.

Thanks,

Randy

We received our parts for our dishwasher within 2 days. It was very simple to find the parts on your site, and very easy to install. Our dishwasher is back to normal and the racks roll in and out easily. I would recommend ordering from PartSelect to anyone.