MHE14XMB2 Roper Microwave - Instructions

I removed the two screws, removed the broken grill, popped in the new grill (after I ordered the correct color, did not get the biscuit color I thought I had ordered the first time) replaced the two screws....I was good to go. Strange that the tabs in the first place just fell apart...but reading others, find this seems to be a common problem. Simple as pie.

Slipped in and screwed top on

Unscrewed 4 different screws, replaced the vent & returned screws. Ack to original positions

replaced the socket per recommendations on this web site. this did not correct the problem.

removed perimeter screws from the bottom side and the lower cover is hinged at the wall side. Motor is visible and easily removed with two screws. Take of the old one, install the new one, and reverse the procedure to put the bottom cover back in place. Will nee helper to hold one side of the bottom until couple of screws can be put in on the other side.

Took 4 Screw on top off...set bottom in first into slots ..pushed top in under the top of outside cover ...put Scews back in.

First, we had to clean up all the interior surfaces, which was just cleaning. There was no internal damage. Then, just setting the center connector, rotary rollers and glass plate. Simple

used screw driver to pry up old part. lifted right off. line up drive couple drive push on. repair took less than 1 minute to repair. works like new
Very Pleased with Parts Select replacement parts

Took out turntable and swapped out old one with a new bright and shiny
New one, ring that is. It was easy using the part from parts select
Thanks
Paul

Opened door and put new plate in.

Placed order on Thursday evening and received Sat Am

Bought a new one. Perfect match, easy replacement.

Removed bed two screw replace grill

Whirlpool Model# MH1150XMS-0 purchased in 2004. I called Whirlpool and they suggested a new microwave. No big surprise - being the thrifty person that I am I wasn’t taking this for an answer. I figured if I had to purchase a new microwave what was $35.22 (part# PS373828 + shipping) if it worked.

I replaced the latch on the microwave door. Once the latch was replaced. I also took this time to make sure that the microwave door was in alignment. Thereafter, I had to adjust the door interlock switch behind the microwave console panel to recognize the microwave being closed. Yes, gaining access to all these areas was a bit difficult but have patience. TADA!!!....microwave is working. #girlsrock

After removing the over-the-range unit (no small feat!) I had to figure out how to open the case (good puzzle!). Capacitor had already discharged, so it was very easy to reach in, pop the old fuse and install the new one! As per your advice, I found out I was a "28%-er"! Upon re-installation, the microwave "sprang to life"!! Thanks, "Part Select"!! I was already shopping around for a new machine! (Now if you could only tell me an easier way to re-mount this heavy beast over the stove!!!)

Ordered a new motor. Removed the outside trim of the oven-microwave combo. 2 screws at the bottom of the trim. Removed the screws that held the combination micro and oven unit in place. Removed the top and bottom black plastic grill of the microwave. 3 screws each. Pulled the entire unit out about 1 inch exposing the screws at each side of the microwave that hold it in place.
Snapped off the top control panel which exposed the wiring connecting the control panel.
Unplugged a couple of wire harness units to free the control panel.
Be sure to label the units to know which goes where during reassembly.
Remove the microwave unit from the housing and place it on its side.
Remove the metal plate that houses the motor. 4 screws hold the motor in place. Disconnect the 2 wires from the old motor and you are ready to install the new motor. Be sure to TURN OFF THE POWER to the unit at the breaker box and remove the turntable from inside the microwave.