MDE6400AGW Maytag Dryer - Instructions

After reading all the other repair stories on Partselect, by the way thank you all, I removed the door, then removed the two security hooks that hold the top secure. Then I removed the front panel. I then marked all the screws on the outer door and shroud so I could easily put it back together. I left the all the wires connected and set the shroud and outer door to the side and removed the drum belt and drum. Removed the spring off the idler arm, then using nutdriver, removed the screw that secures the idler arm to the motor. Assembled the new idler arm parts and reversed the process to put it all back together. If I would have replaced the idler arm assembly the same time I replaced the drum support rollers, I wouldn't have had to do this twice! But now I am an expert repair tech on this particular model.

took old one out then i had to strip the connector off new one was to big...

A year or so ago I replaced one drum wheel. The dryer worked fine for months until it started sqeaking again. When I removed the wheels again the shaft was no longer round but half moon shaped. this allowed the drum to drop lower than it's supposed to. consequently the drum ate through the back drum support. I replaced the back drum support and the roller shafts, in addition to two new rollers. It works great now. The more difficult part of the repair was replacing the rear drum support. It is screwed in from the back and requires two people. Everything else I did by myself. The lesson: If you replace the rollers, be sure the roller shafts are not worn. An asymetric shaft eventually causes more parts to wear out.

I watched the video

Removed the door and machine front.replaced old duct assembly with new ,and reassembled front.

Press in the new female latch part with thumbs. Took about two seconds!

I used a flat screw driver to pop out the old female portion and snapped in the new one. Dryer stays shut. That's it!

Took off the four screws to get to the female clip and used pliers to squeeze it out. Next was using pliers to pinch out the male connector and place the new one in.

First I put the square female end iof the door catch kit nto the square hole as snug as I could. Then I gently pushed the door against the piece until I heard it click in to place. That's it!! Sooooo simple--

I just needed to replace a knob because the original, (plastic) broke. What was great was how soon I received my order, just a matter of a couple of days. I wish I had ordered several as both my washer and dryer have the same ones (five in total) and now another one as broken! I think I will order three or four move.

The replacement part just snapped into place. (The old part had fallen out) It took less than 30 seconds to do the repair.

Watch the video. Very, very easy

Removed four philips screws, two holding door on and two on opposite side of door in order to remove front cover. Then removed two 5/16 screws holding clips that lock the top cover down. Then the top cover hinges up with open access to the drum. The baffles are held into place with two #10 x 1 1/4" screws with 5/16" head each. These had pulled through the drum. Installed new baffles (do NOT come with screws / you'll have to buy some). Had to put small washers (also had to buy) on the screws to hold it onto the drum since the other screw heads pulled through the drum. Closed lid, installed retaining clips, installed door onto frame, installed front cover around door, then screwed door hinges into front cover and screws to other side. Took about as long to write these directions as it did to actually do the work... EASY job!!

I removed the control panel and front panel, then the brace holding in the drum. Then the drum came out easily.

Replacing the rollers is easy, use circlip pliers to remove the old circlips, replace the rollers, and reinstall the circlips.

After removing the idler pulley by removing one bolt and the spring, I replaced the idler roller, again with the circlip pliers. Then the idler arm bolts back to the motor mount, and the spring is replaced.

Reinstalling is easy - place the drum, have someone support it while you install the drum brace, then replace the front panel, then the control panel.

Did an internet search for parts for my older Maytag dryer. Landed on PartSelect and man I am glad I did! Entered my model number and boom! Complete schematics on the dryer, with part numbers. Also have diagnostic questions to point you in the right direction. Figured out what parts I needed, ordered via phone. Fantastic customer service. PartSelect also has excellent installation videos you can watch to assist. Took me a little over an hour to open up the dryer, replace the drum rollers, drum belt, idler roller and both front and rear felt seals. Buttoned dryer back up, hit the run switch and it purs like brand new. I cannot recommend PartSelect to highly. Great company, great customer service, quick shipping.