Maytag/Maytag_Thumb/55904.gif
See part 1 in the diagram
Replacing your Maytag Dryer Multi Rib Belt - 91-5/8 Inches play video
( Grid squares measure 1x1 inch )

Get in touch, we're here to help!

Open until 10PM EST

customerservice@partselect.com

Multi Rib Belt - 91-5/8 Inches

★★★★★
★★★★★
27 Reviews
$31.33   In Stock

Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS11741110
Manufacturer Part Number WP33002535
Manufactured by Whirlpool
Product Description

Multi Rib Belt - 91-5/8 Inches Specifications

This multi rib belt spins the dryer drum during the drying cycle. This belt is 91-5/8 inches in length, 3/8th of an inch wide and has five ridges. It is black in color and made of rubber. You may need to replace the belt if your dryer is noisy or will not tumble.
How Buying OEM Parts Can Save You Time and Money play video

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part fixes the following symptoms:
Noisy | Will not tumble | Will Not Start | Takes too long to dry
This part works with the following products:
Dryer, Washer Dryer Combo.
This part works with the following products:
Maytag, International, Crosley.
Part# WP33002535 replaces these:
AP6007983, 33001777, 33002535, WP33002535VP
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

9 questions answered by our experts.
    Sort by:
    Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
    Louis
    July 20, 2017
    My wife told me today that my dryer is making a really loud noise that is akin to nails on a chalkboard. I know from previous experience that it could be the belt or the rollers but where would you recommend I focus my attention. It sounds like the dryer drum is struggling to spin, but it is still spinning.
    Hi Louis, we recommend checking the rollers for the problem you are experiencing. Rollers are a commonly replaced part because they do wear down over time. The most common side effect of worn rollers are loud screeching noises. If not the rollers, the next step would be to check the blower wheel to make sure it is not broken. I hope this helps!

    13 people found this helpful.

    Was this helpful?
    Thank you for voting!
    Freddie
    July 20, 2017
    I turned on my dryer and it would not rotate, but when I took the clothes out it started spinning. Your site says I need to replace the belt, which I’ve purchased but what else would you recommend I look at as Id rather get it all at once!
    Hi Freddie, if you are already replacing the drum belt we recommend checking the condition of your idler pulley and your rollers. These three parts together are common wear replacement parts, and could all cause a dryer to not spin properly. Good luck with your repair!

    10 people found this helpful.

    Was this helpful?
    Thank you for voting!
    Alicia
    July 20, 2017
    My dryer is making a wining noise and I don’t know what the cause could be. I just replaced the belt and it is turning. TYIA
    Hello Alicia, great question. I would first recommend checking your rollers for visible damage or excess wear. If the sound is not coming from faulty rollers I would also suggest checking the blower wheel for congestion such as dryer sheets and large pieces of lint. Thanks again for your great question!

    6 people found this helpful.

    Was this helpful?
    Thank you for voting!
    Sharon
    July 8, 2019
    My husband replaced the drum belt in june and it broke again, but this time it was frayed. Is there something else he should check?
    For model number MDE8757AYQ
    Hello Sharon, Thank you for the question. I suggest checking the Idler Pulley Wheel and Bearing Part #PS11743032, The Idler Arm and Shaft Part #PS11743033 and the Idler Spring with Rubber Dampener Part #PS2036150. Check for any wear or damaged that can be causing stress on the belt. Hope this helps!

    4 people found this helpful.

    Was this helpful?
    Thank you for voting!
    Related Parts:
    James
    January 18, 2018
    Which way does this drum turn, clockwise or counter clockwise?
    For model number med2500ayw
    Hi James, Thank you for your question. The drum should rotate counter clockwise. I hope this helps. Thank you and have a great day!

    2 people found this helpful.

    Was this helpful?
    Thank you for voting!
    Todd
    February 27, 2020
    Hi, could you please tell me what the model number is for the belt I need for this dryer? Thx
    For model number NDE6800AYW
    Hello Todd, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is PartSelect Number PS11741110. We hope this helps.

    2 people found this helpful.

    Was this helpful?
    Thank you for voting!
    Chase
    April 5, 2018
    Just changed the belt, put my dryer back together and now there is a really hard shake ever 1 to 2 second it spins
    For model number MDE7400AYW
    Hello Chase, thank you for your inquiry. I would recommend checking the placement of the belt, as well as the Idler Arm and Shaft PartSelect Number: PS11743033, Idler Pulley Wheel and Bearing Part Number: WP6-3700340, Drum Support Roller Kit Part Number: 12001541 and the Idler Spring with Rubber Dampener PartSelect Number: 33002459. I hope this helps!

    1 person found this helpful.

    Was this helpful?
    Thank you for voting!
    Jessica
    May 14, 2019
    Is there an illustration of how the belt threads through the motor and idler pulley? I'm having a hard time figuring it out without seeing it in your video.Thank you!
    For model number MDE5500AYW
    Hello Jessica, Thank you for the question. Very sorry but the video is all we have at this time. For more specialized assistance or to speak with someone about this, I would suggest calling the manufacturer of the appliance directly. Hope this helps!

    1 person found this helpful.

    Was this helpful?
    Thank you for voting!
    Sharon
    July 20, 2019
    my husband replaced the drum belt in June and it broke again, but this time it was frayed. Is there something else he should check? For model number mde8757ayq. everything seems to be drying except the towels are damp when the cycle is finished.
    For model number MDE8757AYQ
    Hello Sharon, Thank you for the question. I suggest checking the Idler Pulley Wheel and Bearing Part #PS11743032, The Idler Arm and Shaft Part #PS11743033 and the Idler Spring with Rubber Dampener Part #PS2036150. Check for any wear or damaged that can be causing stress on the belt. Hope this helps!

    1 person found this helpful.

    Was this helpful?
    Thank you for voting!
      Part Videos

      Replacing your Maytag Dryer Multi Rib Belt - 91-5/8 Inches

      Replacing your Maytag Dryer Multi Rib Belt - 91-5/8 Inches play video
      Customer Repair Stories
       Average Repair Rating: 2.8 / 5.0, 73 reviews. What's this?
      Sort by:
      Sorry, we couldn't find any existing installation instruction that matched.
      Dryer squeeking loudly becoming worse quickly
      I received my parts promptly and had no problems, they were accurate and fit well.

      After removing the screws to the front door and panel I removed the wires to the door switch. Carefully I removed the belt and removed the drum. I took the time to vacuum all of the lent from the inside and and remove from all the wiring, motor and heating elements, etc. I replaced the drum rollers, belt, front glides and a buzzer that was on the blink. I reassembled the dryer and unforetunately the dryer was still squeeking. I later repeated the process and found that the tensioner wheel for the belt was the culprit. I cleaned then greased the bearing portion and replaced it. I reassembled the dryer a second time and now it's quiet as a mouse. By the way, you will need a rivet gun to replace the front glides and I recommend you give the belt tensioner wheel a good inspection the first time.

      If your dryer is squeeking, go ahead and order the tensioner wheel also, it's a little money spent toward making sure you get rid of the noise! It might save you a lot of time and trouble.
      • Mark from Lafayette, LA
      • Difficulty Level:
        Easy
      • Total Repair Time:
        1- 2 hours
      • Tools:
        Nutdriver, Pliers, Screw drivers
      345 of 429 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Motor buzzed and dryer drum would not spin when pressing start
      From the first time the motor buzzed (but dryer tumbler then started to turn), 2 weeks elapsed for the dryer drum to stop turning altogether. If this occurs, DO NOT continue to push the start button because the motor armature wiring will heat up and the insulation will begin to melt and smell - a SAFETY HAZARD. Unplug dryer and lockout/tagout as appropriate.

      Through basic troubleshooting, discovered the motor had seized up. Since the unit was about 10 years old and it had to be disassembled for replacement, the decision was made to replace "likely to fail mechanical components including motor, belt, both rear drum rollers/shafts, idler arm pulley/assembly/wheel, associated washers, snap rings and both front glides. Reviewed the PartSelect website and drawings, ordered the parts and they delivered on time. Buy the correct sized snap rings at a local hardware, they're much less expensive. Also once inside your dryer, you'll likely find alot of lint to vacuum out...have fun.

      I went online and Googled several resources that showed how to remove the front dryer panels, as well as PartSelect repair stories. From that point on, I took photos as I was disassembling so I would know how to put it back together. Utilize pictures or whatever system you prefer to keep track of taking something apart and putting it back together.

      Remove the dryer door, then the front panel Disconnect wires to the light, dryness sensor and door switch. Note belt and pulley configuration that is near the motor-this will help you later when reinstalling the belt. Also note if the ribbed side or the flat side of the belt is against the outer drum wall. Remove the door shroud.

      Slip the belt off the idler pulley wheel. Remove front drum support, then dryer drum Note which end of the dryer drum is the front and the orientation of the glides on the drum support. Discard old belt. Drill out and remove the old front glide supports, then install/rivet the new glides.

      Remove both old rear drum rollers/shafts, washers, etc. The rear drum roller shafts are secured to a back bracket by a hex nut....feel around you'll figure it out. Replace new roller shafts. Lightly grease using a high quality silicon grease, then replace new washers, roller, snap ring, etc

      Carefully unplug wiring harness on motor, there are fragile clips on each end. Don't forget a separate ground wire from the harness is attached to the motor mount bracket. Carefully release tension on the idler arm spring. Using the correct size nut driver, remove three screws (on this model) then take out the motor/idler arm assembly. Remove the old idler arm/pulley assembly. Remove the motor mount clips on each end of the mount (I used a wide blade screwdriver). Remove and replace the motor. Motor configurations changed after Whirlpool bought Maytag, so orient it correctly insuring mounting gasket "nubs" on each end of the motor correspond to the cutouts on the motor mount. Reinstall the motor mount clips. Replace the new idler arm assembly/pulley wheel; grease moving parts with high quality wheel bearing grease. Replace motor/mount bracket assembly back into the dryer. Replace ground wire to motor mount bracket and plug wiring harness back in. Reinstall idler arm spring.

      Place belt back on the dryer drum and move into place on rear rollers. Reinstall front drum support. Dryer drum should turn relatively easy. Insure belt is oriented on the drum correctly before connecting belt to motor shaft end and idler arm wheel pulley (the picture you took comes in handy here).

      Reinstall the rest of the parts in reverse.
      191 of 270 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Squeeling on startup and intermittently during use
      First, I read reviews on this forum. Great help! I was betting, from previous reviews, that it was a drum roller. I took everything apart prior to ordering any parts. Sure enough, one drum roller was seized on the roller shaft. Decided to replace all rotating parts (rollers,shafts, belt, idler pulley) while everything was apart. I also took the opportunity to clean out all of the lint (there was a lot) from the motor and intake.
      Parts were on my doorstep in two days. The dryer is like brand new. I could do this job again in less than an hour. This was money and time well spent.
      67 of 78 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      The dryer was making a terrible noise that sounded like bearings squealing.
      I've never even opened this dryer before so I looked at one of the installation videos PartSelect has. I found one using my model, which made it really easy. I removed the front panel and door, then lifted the top of the dryer up on it's hinges: that's a great feature because you need the top out of the way to remove the drum. I took the belt off the drum, lifted it up and pulled it straight out. I did buy a pair of snap ring pliers to remove the snap ring off the drum support shaft. I think you really must have those to remove and replace the rings. Be careful when removing the snap rings. I shot the first one across the room like it was a rubber band. We had a good laugh. I used a wrench to hold the nut on the backside of the roller shaft and unscrewed it. I screwed the new roller shafts on, slipped the drum rollers on them, then carefully used the snap ring pliers to place the rings on the front of the shaft to hold the rollers on. While I had the unit opened up, I figured I should go ahead and replace the multi rib belt. I put the ribbed side on the drum and sat the drum on the rollers . The tricky part is now getting down on the ground, reaching under the drum for the belt. Make sure the belt isn't twisted anywhere on the drum or in your hands while you pull the belt under the idler pulley. Hold the belt ribbed sides together while feeding the belt under the pulley. It takes a good deal of strength to move the pulley over so you can hook the end of the belt on the shaft. Once you've gotten that attached, put your hand inside the drum and rotate it a few times to make sure you connected it properly and that you placed the belt in the right spot on the drum. It was easy to see the black stripe around the drum where I'd taken off the old one.
      65 of 72 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Idler Pulley worn, squeaking
      Did an on-line search on Matag dis-assembly, pulled front panel, dryer drum, replaced idler pulley, rollers and belt. Also, vacuumed dryer cabinet , now the dryer works like new. This is an easy repair for anyone with any mechanical ability, and just basic tools.
      43 of 1399 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      dryer was noisy, tumbler rollers and shafts wore out
      disassembled dryer and removed and replaced rollers and shafts and installed new belt while i was at it. very easy fix, ordered parts from PARTS ELECT.COM , excellent website with great views of my machine made it east to order correct parts.very fast delivery , will use partselect again! HIGHLY RECOMMEND
      42 of 1398 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Metal on Metal Squealing Noise
      After taking the dryer apart, I found that one of the drum support rollers was barely hanging on the pin and was the main cause of the metal on metal squealing noise that became increasingly worse over a month's time.

      I replaced both rollers, the idler pulley, and put on a new belt after giving the dryer a thorough cleaning.

      It was a 100% success and fixed the problem making the dryer work and sound like brand new again.
      • John from Bethlehem, PA
      • Difficulty Level:
        Really Easy
      • Total Repair Time:
        30 - 60 mins
      • Tools:
        Pliers, Screw drivers, Socket set
      32 of 33 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Blower wheel broke
      Replaced bower wheel, drum rollers,belt and Idler pulley while the dryer was apart. so far so good. Easy repair
      Motor bearings seemed tight so hopefully will get another ten years out of dryer.
      24 of 654 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Installation of parts solved the difficulty!
      I watched all of the video provided for repairing each of the parts and used them several times! They were excellent and beneficial! I used the suggestions provided and found the involved correction to do exactly as planned. The end result was very good and the dryer now works like it is supposed to without any noises. I thank you for all of your help.
      21 of 699 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Loud screeching noise
      I watched the very helpful video provided by Parts Select. The repair went smoothly except for two problems. After reassembly, there was still a noise coming from the rotating drum, which I later discovered was the result of not making sure the felt gaskets around the front and back edges of the drum were not being pinched. Smoothing the felt solved the problem. The other issue was that after the repair the dryer was shutting off prematurely, before the clothes were completely dry. This was again my fault. When I first removed the bulkhead, a wire to the automatic moisture sensor came loose without my noticing it, hiding itself deep inside the cabinet. Since the model used on the video did not have such a sensor, disconnecting/reconnecting the wire was not mentioned. Upon reopening the cabinet, I noticed the loose wire and reconnected it -- problem solved. Thanks Parts Select, and thanks to the other user reports that provided useful tips.
      • Cameron from Kerhonkson, NY
      • Difficulty Level:
        Easy
      • Total Repair Time:
        1- 2 hours
      • Tools:
        Nutdriver, Screw drivers
      20 of 713 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Customer Reviews
      Average Rating:
      ★★★★★
      ★★★★★
      27 Reviews
      4.9
      Filter By Rating:
      • 5 Stars
        24
      • 4 Stars
        3
      • 3 Stars
        0
      • 2 Stars
        0
      • 1 Star
        0
      Sort by:
      Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
      Model Cross Reference
      This part works with the following models:
      PartSelect Number: PS11741110
      Manufacturer Part Number: WP33002535
      Brand
      Model Number
      Description
      Crosley
      CDE4205AYJ
      Dryer - Residential
      Crosley
      CDE4205AYW
      Dryer - Residential
      Crosley
      CDE4205AZJ
      Dryer - Residential
      Crosley
      CDE4205AZW
      Dryer - Residential
      Crosley
      CDG4205AWJ
      Dryer - Residential
      Crosley
      CDG4205AWW
      Dryer - Residential
      Maytag
      MDB9206AWW
      Dryer - Maytag Dryer Model MDB9206AWW Parts
      Maytag
      MDE14PDACL
      Dryer - Electric
      Maytag
      MDE14PDACQ
      Dryer - Electric
      Maytag
      MDE14PDACW
      Dryer - Electric
      Maytag
      MDE14PDADL
      Dryer - Electric
      Maytag
      MDE14PDADW
      Dryer - Electric
      Maytag
      MDE14PDAGW
      Dryer - Electric
      Maytag
      MDE14PNAGW
      Dryer - Gas
      Maytag
      MDE14PNAYW
      Dryer - Gas
      Maytag
      MDE14PNAZW
      Dryer - Gas
      Maytag
      MDE14PRAYW
      Dryer - Gas
      Maytag
      MDE14PRAZW
      Dryer - Gas
      Maytag
      MDE14PSADW
      Dryer - Electric
      Maytag
      MDE16CSAGW
      Dryer - Electric
      Maytag
      MDE16CSAKA
      Dryer - Electric
      Maytag
      MDE16CSAKQ
      Dryer - Electric
      Maytag
      MDE16CSAYA
      Dryer - Electric
      Maytag
      MDE16CSAYQ
      Dryer - Commercial
      Maytag
      MDE16CSAYW
      Dryer - Electric
      Maytag
      MDE16CSAZA
      Dryer - Electric
      Maytag
      MDE16CSAZQ
      Dryer - Commercial
      Maytag
      MDE16CSAZW
      Dryer - Commercial
      Maytag
      MDE16CSDGW
      Dryer - Electric
      Maytag
      MDE16CSDYW
      Dryer - Electric

      Get in touch, we're here to help!

      Open until 10PM EST

      Contact Customer Service