Maytag/Maytag_Thumb/6684.gif
See part NI in the diagram
( Grid squares measure 1x1 inch )

Get in touch, we're here to help!

Open until 10PM EST

customerservice@partselect.com

Screw

$6.54   In Stock

Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS11757438
Manufacturer Part Number WPY014874
Manufactured by Whirlpool
Product Description

Screw Specifications

Sold Individually.
How Buying OEM Parts Can Save You Time and Money play video

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part works with the following products:
Dryer, Washer, Washer Dryer Combo, Air Conditioner.
This part works with the following products:
Maytag, Amana, Speed Queen, Crosley.
Part# WPY014874 replaces these:
AP6024088, 014874, 14874, 211880, 310386, 32671, 56086, 9-11039, 911039, M0216544, R0600031, R0600102, Y014874, Y310386
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Customer Repair Stories
 Average Repair Rating: 2.9 / 5.0, 5 reviews. What's this?
    Sort by:
    Sorry, we couldn't find any existing installation instruction that matched.
    The drier tumbler stopped spinning, and my wife noticed a burning smell when it ran.
    1) Took off the front door of the drier (first unscrewed it in the sides, then lifted the door to lift the hinges up and pulled the door off)
    2) Pulled the front panel down and off
    3) I checked the belt to see if it was broken and it wasn't
    4) I tried to turn the drier barrel manually to see if I can move the belt... it didn't move. Not knowing if there was just too much resistance, I tested the drier while looking at the motor and motor pulley as it ran.
    5) I noticed that the motor pinion rotated, but the belt was slipping against it... that's why it smelled. The rubber was burning
    6) Then I found that the idler pulley had stopped rotating, and the belt actually cut a channel into part of the plastic... That's when I realized that I had to replace at least the idler pulley.
    7) Not knowing whether the bushing and other parts were going to be salvageable, I ordered parts for the whole assembly... but I wasn't sure how to best approach the repair...
    8) Then I found partselect.com, and they had both diagrams of the assembly, all the parts easy to order, and best of all, a video of someone actually going through this repair! I was dumbfounded! :)
    9) For swapping the parts I just watched the video on how to pull out the drier barrel... the only difference is that I didn't see a need to unplug the cables from the front top panel before removing the drier tumbler. (Obviously the power was turned off :P)
    10) when I removed the barrel, I swapped the whole idler pulley assembly, just keeping the original spring.
    11) Put everything back together, and it ran like a champ!

    The video helped me save a lot of time though... it showed me how the whole thing is most easily serviced and made the repair a breeze!
    40 of 1348 people found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
    Dryer made loud screeching noise.
    After reading all the other repair stories on Partselect, by the way thank you all, I removed the door, then removed the two security hooks that hold the top secure. Then I removed the front panel. I then marked all the screws on the outer door and shroud so I could easily put it back together. I left the all the wires connected and set the shroud and outer door to the side and removed the drum belt and drum. Removed the spring off the idler arm, then using nutdriver, removed the screw that secures the idler arm to the motor. Assembled the new idler arm parts and reversed the process to put it all back together. If I would have replaced the idler arm assembly the same time I replaced the drum support rollers, I wouldn't have had to do this twice! But now I am an expert repair tech on this particular model.
    6 of 8 people found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
    Squeeky dryer
    Okay, first of all, just let me say, if I can do this, ANYONE can. I am not very handy when it comes to things like this. I watched online videos and they will walk you through everything. I am so pleased with the results. Quiet as can be now. Before, we would have to shut the door when it was on because the scretching was so loud! The parts on this site were far more affordable than at my local repair store and they all came right to my doorstep. Overall it took me about 45 minutes and three beers :) Good luck!
    3 of 3 people found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
    Idler pulley arm mounting screw stripped
    This should have been a simple repair, but turned out to be time consuming and moderately difficult. I hope these instructions will help anyone who encounters the problems described here.

    After a period of the dryer not being used, the idler pulley wheel froze on the shaft of the idler pulley arm, so I needed to replace both parts. After mounting the new wheel and two washers on the new arm and securing with a retaining ring, I went to install this assembly by going in through the small access panel at the rear of the dryer. I slid the belt off the old idler pulley wheel and unhooked the spring from the idler pulley arm; the arm was mounted on a sleeve fastened to the motor bracket by one screw. All that should have been necessary was to back out that screw and replace the old idler pulley assembly with the new one.

    That is where the trouble started. Backing out the screw with a socket driver, I found it would go a few turns, then start to bind. I tried turning it in and out to get the threads to engage, but it kept binding. Eventually I gave the screw a hard turn, and then it would turn freely but not move in or out.

    Looking on the internet for advice, I found a video that asserts for another model Maytag dryer using the same type of mounting for the idler arm, that there is a design flaw. You can find the video by searching for “Maytag dryer idler pulley defect”. According to the video, the sheet metal screw used to mount the idler pulley arm can gradually loosen due to the pressure and vibration, and begins to “waggle” which eventually damages the threads. I believe this is what happened to my dryer. The video suggests replacing the sheet metal screw with a machine screw and nut for a more durable union.

    So now I understood how the screw could be stripped just sitting in the dryer, but that didn’t help me get the screw out. Working through the rear access panel, I tried pulling on the screw head with several types of pliers, pushing the point from behind with a piece of wood while turning the head with a socket driver; eventually I was able to use a pry bar under the screw head and sleeve to apply pressure while turning the head, and with that method the screw backed out. With the screw removed, it could be seen that the threads in the middle part of the thread length were almost completely worn away.

    The screw sleeve got somewhat deformed in this process so I ordered a new one, along with an exact replacement sheet metal screw, hoping the threads in the hole were still intact. With the old idler pulley arm now removed, I could transfer the old idler bracket spacer to the new idler pulley arm. When the ordered parts arrived and I tried to mount the idler pulley arm, the new screw would go in only a couple of turns before binding. Rather than risk winding up in the same situation by forcing the screw, I decided to use a machine screw and nut instead.

    The original sheet metal screw was a #10. A machine screw the same size would not fit through the hole, and I could not fit my drill into the dryer cabinet in a position to enlarge the hole, so I used a #8 machine screw with a nut and lock washer. First I put some grease on the contact areas of the screw sleeve and idler bracket spacer, then inserted the machine screw through the hole and put the lock washer and nut on the other side of the mounting. The space around the nut is very limited, and most of my tools were too large to hold the nut while the screw was tightened. It was too small for a socket or adjustable wrench, and the clearance from the exhaust duct was too small for the handles of most tools. Eventually, I found a needle nose pliers with short handles that did the job. A thin open end wrench might also work. Then I reconnected the spring and belt to the idler pulley assembly, and closed the access panel. So far the dryer works, but if the #8 screw turns out to be not strong enough, I could get an extension for my drill and enlarge the hole to fit a #10 machine screw and nut.

    Looking back on the job, the most difficult part of this repair was removing the damaged screw. This and several other steps might have been a lot easier if I had removed the motor bracket (where the idler pulley arm is mounted) from the dryer and worked outside the cabinet. Part Select has an excellent video “Replacing the Drive Motor” that shows how to do this. It would be a lot of disassembly work, but for someone with good assembly skills could be easier in the long run.

    Hopefully most folks out there who replace the idler pulley arm on a dryer will find an easier situation than I did. But for any who have to deal with a stripped mounting screw, I hope this summary will help you resolve it.
    • Alan from BETHESDA, MD
    • Difficulty Level:
      A Bit Difficult
    • Total Repair Time:
      More than 2 hours
    • Tools:
      Nutdriver, Pliers, Screw drivers, Socket set
    • Parts Used:
      WPY014874, WP315772
    1 person found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
    Loose from wear.Caused belt to break
    Took off the back and replaced after replacing belt and spring
    • David from Lemont, IL
    • Difficulty Level:
      A Bit Difficult
    • Total Repair Time:
      1- 2 hours
    • Tools:
      Nutdriver, Screw drivers
    • Parts Used:
      WPY014874, WP315772
    0 of 3 people found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
      Model Cross Reference
      This part works with the following models:
      PartSelect Number: PS11757438
      Manufacturer Part Number: WPY014874
      Brand
      Model Number
      Description
      Amana
      100A-3PH
      Air Conditioner - Room
      Amana
      100A-3R
      Air Conditioner - Room
      Amana
      100A-3RH
      Air Conditioner - Room
      Amana
      100A-8R
      Air Conditioner - Room
      Amana
      12E
      Freezer
      Amana
      12F
      Freezer
      Amana
      12G
      Freezer
      Amana
      12H
      Freezer
      Amana
      12J
      Freezer
      Amana
      12JI
      Freezer
      Hoover
      15
      Freezer
      Amana
      150A-3PH
      Air Conditioner - Room
      Amana
      150A-3R
      Air Conditioner - Room
      Amana
      150A-3RH
      Air Conditioner - Room
      Amana
      150A-8R
      Air Conditioner - Room
      Amana
      150C-3R
      Air Conditioner - Room
      Amana
      150C-3RH
      Air Conditioner - Room
      Amana
      150C-8R
      Air Conditioner - Room
      Amana
      150C-8RH
      Air Conditioner - Room
      Amana
      15A
      Freezer
      Amana
      15B
      Freezer
      Amana
      15C
      Freezer
      Hoover
      19
      Freezer
      Amana
      19A
      Freezer
      Amana
      19B
      Freezer
      Amana
      19C
      Freezer
      Amana
      200A-3PH
      Air Conditioner - Room
      Amana
      200A-3R
      Air Conditioner - Room
      Amana
      200A-3RH
      Air Conditioner - Room
      Amana
      200C
      Air Conditioner - ROOM AIR CONDITIONER

      Get in touch, we're here to help!

      Open until 10PM EST

      Contact Customer Service