MAT15MNAWW0 Maytag Washer - Instructions

Took two hosses off with pliers and snaped the clips off then pulled pump off of shaft . replaced with new pump. VERY EASY. Thanks Brian

removed two hose clamps and two metal clips
removed old pump and replaced with new
wish all my plumbing was that easy
order Thursday night got it Monday
great job
I'll be telling everyone that needs parts about you
thanks

Kayla tilted the washer backwards so I could get access to the pump from below. all I had to remove was two clips then slid the old pump off the shaft and the new one on-clip it in place.Then clamp the hoses on the new ports and we were done in about ten minutes.This made me feel good in three ways... Did A job with my daughter! Save a lot of cash!! and walk away with a great sense of accomplishment !!! Rob@kayla

got under machine and replaced pump

I turned the washer on to see if I could determine where it was leaking from. After I figured out that it was the pump that was leaking, I ordered a new pump. I went with next day shipping because at our house, we can't go long without a washer and the cost for the shipping was worth it. Had it installed in 10 minutes, only tool needed was a pliers to remove the hose clamps, piece of cake repair!

The new pump arrived at my door just a few days after it was shipped.

Once I got the water hoses off and the clips holding the pump I had to use a large screwdriver to get the pump off the motor shaft. I then tried putting the new pump on but it wouldn't fit. I noticed that the motor shaft was flaired out (possibly due to rust) so I used a Dremel Tool with a grinding disk to carefully grind down the shaft to what it looked like it was supposed to be. Once that was done the pump easily slipped into place. I attached the pump clamps and hoses and pushed the washer back into place. I ran a quick test and then later a load of laundry. No more leaks!

I read the trouble shooting guide on your web sight to figure out what the problem was and after checking the hoses the pump seemed the next most likely problem. So I ordered the part.My main problem was the lack of room to work,if I could have tipped it on it's back or raised it I would not of had a problem.But I tipped it up and blocked it from falling and removed the part while waiting for the new one to arrive.Once it arrived it only took a few minutes to install.When I tried the washer it still leaked water,so I tipped it back up to check it out.The only thing that was wrong was that the spring hose clamps had not seated yet so I moved them around and wiggled the hoses to try and get them tighter.The next time ,it worked fine.The other reviews and trouble shooting guide were a great help!

the hard part was getting the pump off of the rusted centerpeice. i actually had to grab the pump with both hands, put my feet on the rotator and PULL. finally it basically snapped off and rusted peices went flying. after cleaning it the new pump went on rather easily, with the help of a rubber mallet.

I propped the unit on its side, then I removed the intake and discharge hose with pliers (remember to have a bucket handy for the extra water in the hoses.)
Secondly, there are two clips on the top and bottom of the pump which hold the unit snug against the motor. These simply pop off with your hand or a screwdriver (be careful to save these!) Now the pump should slide off the drive shaft easily but most likely it will not due rusting of the shaft. A pry bar or large screwdriver and some elbow grease will get the pump to slide off.
Installation is the reverse except you will have to sand off the rust on the shaft. Sand paper will do but I used a Dremel type grinder (die grinder) which made easy work of removing the rust. Finally, sliding the new pump in is remarkably easy.
Installation of the new pump should take less than 10 minutes with a clean driveshaft.

Remove four screws securing control panel from the rear and tilt control panel forward. Unplug wiring harness from door limit switch. Unsnap and remove two S-clamps securing enclosure to back panel. Tilt enclosure slightly forward and remove it from wash machine. Disconnect water hoses and clips securing water pump and remove water pump. Install in reverse order. Caution: inspect water hoses closely. I had a rotten pump intake hose and found out the hard way (water everywhere).

It was the first time I ever ordered parts online or even attempted to repair a washer. You all have made finding and ordering the right part very easy. I got the part in 2 days even though I used the cheapest shipping option (5 to 7 days). I turned off the water, removed the water lines so I could lay the washer on its side. No tools were needed to remove the water pump, just two clips held it on. I put the new pump on, hooked up the water and washed a load that night.

Disconnected power, water, and drain then moved washer away from wall. Put down some 2x4's to protect hoses and flipped washer on its back. Removed hoses with pliers, removed clips holding pump to shaft, and installed new pump. Reversed process and tested with just water be fire washing clothes.

Frist I removed the two water hoses going to the pump. Second releaseed the two clips holding the pump , it came right off the motor shaft.
Third, put the new pump on the shaft, put the clips on last the hoses good to go.

My husband got the part within 2 days of the order and replaced the leaking pump within a half hour. The repair was very quick and easy for him and your company's prompt delivery prevented my floor from getting wet everytime I did a load of laundry. Thank you and we will continue to get parts from your site in the future--hopefully we won't need to anytime soon. but we know you are there if we need to repair!

Pull Washer out, Flip to the right on it's side. Pop two Metal retaining clips, squeeze hose clamps with pliers. Remove pump, sand shaft with dremil or 80 grit sand paper. Replace with new pump. Easy! Push washer back and attach hoses and power. Done 15 minute repair