MAT15MNAWW0 Maytag Washer - Instructions

This model is a compact / apartment size washer and the repair was fairly easy. The lid is held on by 2 spring clips on the front and 2 tabs on the rear. I used a screwdriver to pop the top off the clips, removed the screws on the tabs, unplugged the switch and set the top aside. Took out 2 screws (all screws are 5/16" hex head) on the left side panel (facing the front of the machine) and set it to the side. The pump is clearly visible at this point. Tipped the washer and propped it up for easier access. Removed the 2 hose clamps (set a pan underneath first) and the pump is held in place by 2 spring clips. Popped those off and the pump came right out. Put the new pump in, snapped the spring clips on, put the hose clamps back in place, the side panel and the lid. Not at all hard to do. About 30 to 45 minutes and I was doing laundry again.

Tried to follow videos. Couldn't figure how to raise top. Laid machine on front used pliers to unclip bracket and clips holding hose. Took 10 minutes to work it this way.

Old machine and vibrations are still there but weaker. Seemed to turn counter clock wise. Put a 4x4 board behind in order to stop the twisting, and keep hoses safe from vibrating and causing wear. Stays fairly stable now.

Well, after resolving Part Select (PS) shipping issues (PS sent me two refrigerator glass shelves instead of a Tub Spring); And as it turns out they sent me the wrong part for the suspension pads, which I have returned for credit. It takes 3-4 weeks to obtain your credit BTW.

Well after removing the cabinet, agitator, wash basket, plastic tub, all 5 springs, & pump suction line, I was able to access the Tub wear pads and suspension pads. As it turns out the suspension pads looked good.
Thank God, as PS had sent wrong parts. I replaced the wear pads, the 5 springs, and reversed the disassembly process. Took about 6 hours.
But washer works fine now, still vibrates, but does not walk across floor any more.

It was a miracle. We were going to get rid of the washing machine because it made so much noise and rattled the whole house. It also 'walked' across the room with every load.
I simply replaced the wear pads (2 of them were already worn away), and now it is as quiet as when it was new. AMAZING!

Replacing the clutch was easy but unfortunately did not fix the washing machine. I couldn't get the agitator loose at first, but it came loose when I unbolted the motor and transmission assembly. After replacing the clutch and reassembling the motor, I tilted the washer back up and found that the basket in the center under the agitator was cracked all the way around and that was why it wasn't spinning. It was also why the clutch was burning--trying to spin a basket that wasn't centered in the drum anymore. This washer is over 25 years old, so I decided not to replace the basket, since a replacement is about $400. A good attempt at an inexpensive repair, but unsuccessful.

Very easy replacement. The new hose was more like a formed radiator hose and fit exactly.
Removed two screws at rear of control panel and separated the rear cabinet panel from the front cabinet enough to get to the water valve. I then disconnected the break hose from the valve by compressing the spring clamp. I then disconnected the other end from the washer water inlet by also releasing another spring clamp.
The new hose was installed using the same clamps. The cabinet was reassembled and washer tested for leaks.

Removed washer shell by instruction via video, then easily installed break hose and clamped it back on to water line and water dispenser. Works like a charm! No more leak

I followed the instructions in the video on the part page (part #PS11741239), which was also conveniently linked in the item shipped email. The replacement of the part was very easy ... the hard part was balancing the washer again (kitchen floor seems to have sunk in the middle). Back to normal function without having to suffer a flood first. Thanks.

I could not make the repair. If you get the pump specified on the shaft that drives the pump, the pump will be broken. I tried to call, nobody answers the phone. I ended up buying a Washing Machine and I'm stuck with a pump I cannot use.

replaced missing screw and pad and now machine works perfectly

I tipped up the machine and had my wife hold it.
I removed the two hoses with water pump pliers. Then , I removed the two clips with my fingers. The old pump came off in my hands. I installed the two hoses on the new pump with my hands, lined up the pump drive with the hole pushed it in and re-attached the two clips with my hands.
The whole job took maybe five minutes. The hardest part of the job was conviencing my wife that there was no danger involved with the process.

very easy to repair , instructions very clear , parts person very good to talk to, parts got here fast

Tilted washer back, pump was right in the front on bottom. Removed two spring clips, pump pulls off. Removed two spring clamps and hoses. Reconnected hoses and spring clamps to new pump, put pump back on, put clips back on, dropped washer, put washer back in place. Done. 10 Minutes, max. My twelve year old son could have done it. Part was less than fifty bucks, and service companies want an additional 150 bucks to do the job. Thanks, PartSelect!!

It was a simple & quick repair. pulled the washer forward leaving everything connected except for the electric.. simply unplug it. then tipped the washer backwards. with a droplight & a screwdriver and a pair of pliers replaced the old pump by taking off the metal clamps that were bracing the pump plus the clamps for the hose. also is a good idea to have a pan for the extra water that will drain from the old pump.remove & then put on the new pump & add the clamps you removed. it only took about 15 mins & was alot cheaper than to go buy a new washer. everything works great.