MAT15MNAWW0 Maytag Washer - Instructions

Isolated problem to front section of washer by elevating and adding water. Once I identified the pump as leaking (it was pretty obvious:>)I used a screwdriver to release the snaps that hold the pump to the drive motor. After sliding the pump off of the drive motor I used the pliers I release the clamps on the two hoses. Next I logged on to Partselest.com and ordered a replacement. The item arrived in two days. I placed the pump on the motor first then connected the hoses. It was much easier to slide the hose clamps to the proper position with the pump held secure on the motor.

I disconnected the washer from the water supply lines.turned the washer on it's back. took two hoses off the water pump.Unsnapped two spring clip's.Took the old pump off and installed the new pump.That is all there was to it.

First, I laid the washer upon its back and removed the two clamps that held the water pump in place.
with wire pliers.
Next I removed the two inlet water hoses from the pump and sat that pump aside. I then placed the new water pump upon the shaft of the washer and secured the two water inlet hoses back on the new pump wth the clamps. I tightened them with the wire pliers slipping the clamp upon the hoses. Lastly , I snapped the two wire clamps that hold the pump in place back in their groves and immediately placed the washer up right .

I press using the plier the spring retainer to removed the two hose from the defective pump.
I used screw driver to removed the two retainer.I pulled the pump away from the shaft of the motor. Replaced with new pump, align to the motor shaft and return back the two retainer. It is easy and its good to have my parts right on time.

Removed the four screws from the control housing. Disconnect wire to machine housing. Remove the two clips connecting the machine housing to the back. Remove washing machine housing. Pump is located right in front. Disconnect hoses, remove and replace pump, reconnect hoses. Replace the machine housing. This was the hardest part if all trying to reinstall the housing.Once you get the machine housing in place correctly, put everything back together. You just saved about $125 in fifteen minutes.

very well the part was easy to install and the part was easy to find on the diagram furnished by parts select

The repair went fine and the U - Tube video was very helpful. However, the putty knife under the front corners to release a spring clip was not accurate to release the console. Our Roper had two philips head screws on each corner of the back of the console that had to be removed to allow the console to slide back and off its clips. Then the housing of the machine (sides and front) was not coming off as described. However, after measuring I determined that the water pump had enough clearance to be removed without the housing of the machine being removed. So, the repair was even simpler than described.

I watched the instructional video on how to take apart and how to take washer a part and how to install the direct drive water pump. It was very easy to do. also the delivery was very fast. I will be using the site to fix other appiances that I have that is sitting around broken. Thanks for your speedy service and customer service.

watched a video that showed how to repair that you had on your web site. also read some of the remarks that other people left on site, one was super easy. just laid washer on its back, unhooked both water lines from pump. unhooked both metal clips holding pump and pulled off. replaced new pump in reverse order. didn't have to go thru all the procedures of taking off the body or nothing. 15min job.

tilted the unit on it's back. removed clamps and hoses from pump. used screwdriver and pried off 2 hold-down clamps. removed old pump. placed new pump onto shaft. installed hold -down straps. re-installed 2 hoses. stood washer upright, releveled and turned on.

First time .Replace the clutch .miss placed one of the retainer clip .found it after the replacement came .It was in the fold at the base of the machine.

I followed the you tube instructions. The hardest part was realigning the washer housing on the lower frame.

Replaced hinge switch. Still no spin cycle. Noticed hinge bearing cracked & if hinge forced into switch, spin activated. Ordered new hinge bearings.Spin cycle still didn't engage. On further examination, observed that hinge was bent. Straightened hinge & worked like a charm. Didn't really need new switch or bearings. NOTE : Avoid having washer door bang shut.Took longer than expected, but each procedure was simple.

I Removed hose clamps and 2 pump clamps. I took the old pump(had a small hole burned in it) off and replaced it with the new pump. I replaced the 2 pump clamps and the hose clamps and it was ready to go.

My friend unplugged washer turned off water to it, tilted machine back took off old, put on new. It took him about 5 minutes. Washer is working fine now, no more water leaks!