KHEV01RSS0 KitchenAid Dryer - Instructions

It was very easy to repair and the 1-800 number is a grat resource for assistnat in locating the part.

Followed the instructions from the Whirlpool Technical Service Manual available online

I opened up the bottom of the cabinet and found some evidence of burned lint in the heater box. I ohmed out the thermostats and they were good. Then I ohmed out the heater coil and found that it was an open circuit.

Opened the bottom section removed the heater element replaced it and boom!! It works!!!!!

Disconnected dryer from power source. Removed bottom panel on dryer. Removed three screws. Disconnected two wires on heating element. Pulled heating element out. Attached new heating element. Success!

I ordered the Part on Wednesday night, it arrived on Saturday, and was installed by Monday by my husband. This was the best service I have seen in a good while. Kudos to you!

First, we unclogged the blocked duct (which, is apparently what burned up the heating unit in the first place!), then, we took off the front of the dryer panel; then we loosened up the heating unit's case and took out the existing heating unit. It was apparent why it wasn't working. You'll have to see yours for yourself. Then, we installed the new unit, put the heat shield back on, closed up the dryer and turned it on. No heat... oops because we forgot to put the electricity to the unit... so we took the panel back off, then plugged the wires up to the heating unit, as we should have the first time, closed up the panel, and voila! The dryer was working again, and for a major fraction of the cost of replacing the thing! 45 dollars instead of 800. Well worth the time! And the 14 year old did the repair. Explains the first plug in mishap, but also taught him a good skill!!!

Being from the old school where we never assume to know what the problem was, so took out the heating element to inspect which I found that the element had a broken coil which confermed my suspicions. I ordered a new element on Saturday from paRts select on Saturday and recieved it on Wednesday Ann the rest was a matter of reassembling which was a breeze since I foot plenty of pictures.

Remove two screws holding front panel of dryer. Heating element is on right side, in a protective tube. Remove the six wires connected to the tube, noting their placement. Remove two screws from front metal bracket holding in the tube. Pull tube out. One screw is holding the heating element in the tube, so remove that and you can replace the element. Then reverse to put it all back together. Clean out all of the lint inside the dryer.

first turn off the power supply then ..removed the lower front cover. .removed the heat shield that covers the element. .. removed the element and replaced with the new one ..

unpluged dryer removed back cover removed heating element replaced new part and back cover job complete

We removed front cover, then removed the part in front of the element. Removed old element after taking out screw that held it in. Then placed new element in.

removed bottom panel & removed old element.

First I reviewed the diagram to become familiar where items were located. I then insured unit was unpluged I used nutdriver to remove front cover from dryer. Noticed a lot of lint. Good time to vacuum it made finding screws and wires easier.Next Located heating element as described in parts location diagram. Utilized small socket to remove screws in cover plate. the socket set allow easy access to screws under cover plate. Removed 2 electrical wires from heating element. Pull heating element from housing with needle nose pliers. Had to tug a little, inspected element and found break in heating coil.Placed in new element by using reverse installation procedure. (didn't replace lint)This was an easy fix and I saved lots of dollars on repair or hundreds on new dryer. I spent about 20 minutes on the entire project. If you can read you can do this project. Very easy to complete. PS Ordering the parts was easy and arrived earlier than exepected.

First I replaced the heating element. That did not fix the problem, so I used an ohm meter to test the thermostat and fuse (thermal cut-off). One of those was bad, so I ordered the thermostat/fuse conbo and put those in. The hardest part was getting the wires to the right places. I labeled them with masking tape and a sharpie, but maybe they are sized so they only fit one place. I didn't check. The actual work of changing out the parts was super easy. I recommend testing those three parts-heating element, thermostat, fuse-with an ohm meter before buying something you don't need. I now have a spare heating element and thermostat. I should be good for another ten years!