JBP26AY7 General Electric Range - Instructions

Quite hard to do,had to take out screw that went thru oven door,stabilizing piece fell off .We had to get the two screws lined up and thru the door then screw the handle in.but we did it!

I flipped breaker off for electic and confirmed that power to the stove was off. I removed the 2 screws holding the control unit in place. Carefully removed all knobs and buttons and pryed the cover for the control unit off. I then removed old part, removed the wired and clipped wires to the new unit. Put cover back on - has some difficulty getting the panel back in place to line up the screws. But after a couple of attempts, was able to line up unit and put screws in place to secure. Replaced all knobs. Turn breaker back on and cooked lunch. Very easy job. Most difficult part was getting panel back in position. I would watch alignment more carefully before I removed in next time. Easy home repair for Women...not sure about my man?

Good directions

The part was just like the old one and would have been an easy fix except our range suffered from a lighting hit. The clips had melted together. Called a dealer and asked about a new wiring harness. He said in those cases just cut the clip off and hard wire with wire clips,or firecrackers. We used wire nuts and taped all together and the oven works just great. Nothing is ever as easy as it should be.

The original controls were different for the small burners and the large burners. The replacement part fits all. Before removing wires, pay attention to writing on new and old control and replace 1 at a time. The hardest part was being sure to cut the knob stem to the correct length. Control works well.

unplugged the broken elements and plugged in the new ones. Took about one minute. Tools used: hands and fingers.

unplugged burners replaced drip bowls plugged in burners

Not really a repair. But would like to say, I like the price and shipping was super fast. Thanks.

replaced

My husband was able to easily remove and replace the switch and know with-in 15 minutes.

Ordered new parts. Received email with tracking number. Parts arrived as promised. Turned off power at breaker (!). Removed burners and pans. Lifted the lid of the range. Inspected the plugs and discovered one had come loose from bracket and was not in straight. Reset plug in bracket. While the lid was open, placed the drip bowl in opening and installed the burner and made sure the burner was laying properly in the drip bowl. Repeat for each. Perfect fit, If done properly, the small burners should lay down flat and not rock back and forth. I have seen complaints about rocking, and experienced some of it on one burner. Make sure the heating element is set in the plug well and it should work. A little patience may be required to get it just right. Everything lays flat and the stove looks new again. I have purchased from Part Select on other projects including a dryer rebuild and a new face plate for this range. Great products, reasonable prices, wonderful tutorial videos and good service.

I read parts select instructions and i was done in less than 30 minutes. Since 1988, this is the 1st. part that I had to replace. I now have parts select on my favorites list.

slid the range away from wall. disconnect power. removed back,compared switches and marked wires.installed new switch and wires.the adapter for the control knob was a problem it left the knob out futher than original i had to modify the plastic adapter and got it close enought! the most time spent was cleaning up the floor before putting the range back.

Moved the range out and disconnected the power cord. Removed the back cover.Disconnected wires after labeling the them. Removed the unit from the range,Carefully removed the front decal and applied to the new unit. Installed the new unit into range and wired according to the instruction and put the covers back on. plugged back in and tested the range and everything functioned correctly.

The repair was quite simple. I pulled the range away from the wall. Removved 6 screws from the back panel with a nut driver. I the disconnected the wires from the clock control and then removed the 4 screws securing the control board. I loosened the faceplate from the old control with a hair dryer and removed it with a knife. I afixed the faceplate to the new control with two sided tape. Connected the wires to the new control and secured it with the 4 screws. The only problem one might have is the instructions referenced black and purple wires whereas mine were red and blue respectively. Reattached the back panel with the six screws and plugged the power plug back in. Moved the range back against the wall and tested the oven which tested perfectly. Note please disconnect power before proceeding with the installation of the new part.