JBP26AY7 General Electric Range - Instructions

disconnected electricity, used pinch pliers to remove broken ends from connection box and used an already existing element to make sure a new one would work at all. Ordered new one that arrived very quickly and replaced the broken one. After years of taking these in and out for cleaning by outside cleaning help they are bound to break off. I will do the gentle removal from now on.

I located and removed 2 sets of hex-head screws under the front lip of the cooktop, then lifted the entire cooktop to access the burner controls. Removed the wires and taped them, and took out the old control after removing 2 phillips head screws. Installed replacement part easily. Only tricky part is that the various shaft adapters don't quite work with my knob. I'll fix it completely with a bit of epoxy and the adapters they sent.

Pulled the old surface element out and plugged the new one in. Took all of 45 seconds!!!!!

It's nice to know that one can still get replacement parts for 50 year old stove tops!!!!

I simply pushed the new burner into hardware. I then tested it to see if it works. . .

I pulled the old burner out and slid the new one in it's place. Turned on the eye to make sure it worked. Felt heat in a few seconds and turned off.

Just put it right into the receptacle. I want to add...we had gone to our local appliance store and brought home a wrong-size unit. Got online and your website came up. It was easy to find the correct part, ordered it and it arrived 3 days later. I have already recommended your website to 2 of my friends. One very good experience!!!

I removed the drip bowls and pulled out each coil from the plug on the range. Plugged in the new coils and replaced the drip bowls.

After checking at local appliance stores and unable to find the bunner I went online looking. I found this site and there it was. I ordered it, received it within two days, took the old one out and the new one in. As my granddaughter says, "easy peasy lemon squeeze". It took all of five seconds and I'm cooking again.

Removed old burner, plugged in new burner. Turned on electric and everything worked fine. I was concerned that I would not be able to get the correct burner since my stove is approximately 30 years old and General Electric no longer stocks replacement parts. The new surface element was manufactured by General Electric and had the correct replacement number on the package. Thanks Part Select.

it was hard to figure out the instructions from A switch to B switch to my switch. The first switch was no good the second one was good. prayer book didn't hurt.thank

Took the upper back covering off, disconnected the clock control. The only problem is the replacement didn't have the same connections so I was able to pull up the replacement number of wb27x10311 and asked for a diagram which told me exactly where to plug each of the red, white, blue and yellow wires, what a relief! To my amazement I fixed my "old" stove for less than $160, if I had called GE to service it, I'm sure I would have been looking at a $400 bill. This was the way to go, Thank You!

After needlessly replacing the Thermo-sensor and Bake element I was able to determine that, while I had proper voltage to the appliance I did not have power to bake element when bake knob was turned on. The broil element worked properly. I hesitated purchasing the Electronic Clock Control because there was nothing wrong with the oven clock and it was an expensive part. I switched out the control unit and was delighted to see the bake element heat up immediately. It was simple to replace and the instructions that came with it were adequate - just some differences in the color of wires. Thank you Part Select.com!

took the two bolts out of element, pulled the wires and replaced...It was the fast shipping and receiving that made it awsome.. was all done in 2 days..thanx

This repair was quite a bit more difficult then what had been described on the web site. First off, I have a double wall oven that is built in. Sliding it out of the cabinet was difficult and because oven was hard wired, I had to disconnect the actual wiring from the oven back. . Positioning the oven and allowing for it to rest on a support bench was the most difficult part The oven is heavy. Eventually, removing the back and top panels of the oven revealed the sensor connection. I was then able to feed it through the oven and reconnect all the wiring harnesses.. Getting the oven back in the cabinet was equally a challenge. But it did seem to fix the problem with over heating.

This is twin oven range with controls at side of upper oven. Control panel was fastened with screws at top and bottom. Range has built-in hood at top which had to be disassembled to reach top screw. Once had access to top screw, eaisly removed control panel and replaced control. New control had identical connections as old control so only had to install it, break shaft to correct length, and use proper shaft adapter for knob. Remounted control panel and range worked perfectly. This would have been a very quick job except for having to deal with the built-in range hood.