HTAP1100F1WW General Electric Washer - Instructions

I just removed old parts And put the new part on it was very easy to do.

First I removed the screws that held the drain hose clip to the washer. Then I pulled the hose, along with the clip, completely out of the washer. I then took the old hose out of the washer clip and put the new hose in the new clip; I pushed the hose into the washing maching and tightened the hose clip to the maching with the existing screws. Seriously easy, took less than 15 minutes. And I have virtually no handyman skills at all!

replaced them & working fine now....

Removed three nut screws and raised the control panel forward twisted the old switch off removed one wire at a time and put it on the new switch. I did this so the wires would be where they should. After I put the new switch on I replaced the three nut screws I plugged the washer in set it on cold water and it worked like it should.

I watched the video provided by your site and followed it. I removed the clothes softener part from the agitator, Got a good grip on the agitator and pulled up. It came right off. Aligned the new agitator groves and slid it into place, put the fabric softener part back on! Super easy.

Unplug the washing machine. There are electrical components that can injure or kill you. Using a screw driver inserted just below the lid of the washer in the front, there are two (2) spring clips that you push on to release. Then the front of the washer tilts down and you remove it and set aside.
On the bottom right you will see the flexible, convoluted rubber hose connecting from the pump to the washer tub. Two (2) clamps hold the hose on. Remove the two clamps, install the new hose and re-install the clamps. Re-install the front panel and push into place, allowing clips to lock into the front panel.

With screwdriver, I removed screws holding old hose in place. Attached new hose and screwed into place.

I replaced the hose between the tub and the pump. The only difficulty came with the accessibility of the problem area. I just pulled off the front panel of the machine and used a screwdriver and pliers to loosen the attachments and put the new hose in place.

Put the drain hose clip on (it will take squeezing but the hose will pass through). There will be a groove that whose width spacing is similar to the clip. Once that's on, insert hose and screw in the clip.

It tooke some time to figure out where the water was leaking. It was from a small hole at the lateral side of the upper third of the drain inlet tube. Removing the hose was easy. Attaching it to the tub with a hose clamp was easy, but attaching the lower end to the pump motor was quite difficult because the spring clamp that had come with the washer was difficult to manipulate. I had to replace it with a band hose clamp.

By the way, the hole in the hose had been caused by rubbing the hose against the drain pipe from the motor to the sink.

Very easy to put a new water pump. You have to disconnect two hoses from the pump, unplug the power connection from the pump, and unscrew the two screws from the base of the pump.

Took back half off and installed new one

1. take the machine apart, since the noise comes when the barrel is spining, I just watch for anything that contact to the axel.
2. without special tools, it was difficult to take off agigator, and a nut (that tighthened lefthanded).
3. Once defect part found, seach online for the part supply to replace.

Took off the front panel of the washer which exposed electrical wires going to top lid sensor. Took out old sensor installed new. Cut wires from old sensor and spliced wires from new sensor to machines wires that went to old sensor. Replaced front of washer. Washer works fine now.

First I removed the two clamps that hold the inlet drain hose onto the pump. **There may still be water in the hose** This was pretty easy, but a set of vice grips would have been nice. The space is not too cramped, but required a little bit of wiggling. Putting it on was a little bit harder, just because I did not want to tear the hose on the tub or pump inlet. Make sure both are fully seated or else it could still leak. The drain hose and the clip are pretty self explanatory. I tried to buy a generic drain hose at a big box lumber yard, but I could never make it fit right.

Hope this helps.