All Installation Instructions for General Electric Dishwasher GLD5700N00CC

Would only drain intermittenly

Thought it might be check flapper valve on drain pump, so I replaced fairly easily, per instructions. When doing, I noticed the attached relay wires were not secure. When it was on the drain cycle one of the relay wires vibrated badly and loosened the connection enough to only work occasionaly. Would like to put new relay on the pump but they do not sell separately from the pump. (one assembly). I resecured connection and will wait till relay gives out and buy new assembly, but for now it's working perfectly!

Parts Used:

Check Valve Flapper

C. from Lexington, KY
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Old soap dispensor latch would not hold

Turned off the power at the main box. Removed the six phillips screws and two bottom hex screws holding the front panel. Removed the two solenoid wires on the old dispenser (Label wire polarity). Removed the eight screws holding the old soap dispensor and took it out. Cleaned the area around the hole. Laid down a bead of silicon caulk around the hole edges. Placed the new dispenser in the hole and replaced the eight screws (do not over tighten). Replaced the two wires on the dispenser solenoid (check polarity). Replaced the front cover (Do not over tighten. Turned on the power and job complete.

Parts Used:

Detergent Dispenser with Rinse Cap

Kenneth from Dublin, OH
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Detergent dispenser did not work

Followed the instruction video on your website. It was accurate and valid. The repair should have taken 15 mins., instead one of the screws holding the dispenser was frozen. Tried DW-40, and liquid wrench. Neither worked because the screw was in plastic.Finally got out the Dremel and cutting wheels. Had to cut away enough of the unit until I could get at the screw (it was the center bottom one). Sliced through some more of the housing, then cut a notch in the screw head deep enough so I could apply enough pressure with a flat blade screwdriver to open it. After that things went as smoothly as could be expected.A bad design and cheap materials.

Parts Used:

Detergent Dispenser with Rinse Cap

ARTHUR from OAK PARK, IL
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

wouldn't drain

Removed the dishwasher to get at the defective parts and removed,than replaced the two check valves and reassemble.

Parts Used:

Check Valve Flapper

JOHN D. from GOSHEN, IN
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)

3 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Leaking hose

You tube
Just mack sure the electric is off - breaker and live wire check pre starting

Parts Used:

Dishwasher Clamp

Adaptor Pump Assembly

Inlet Sump

CLAMP

JANET from SANDY SPRING, MD
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers, Wrench (Adjustable)

1 person found this instruction helpful.

Was this instruction helpful to you?

Difficult to install the mounting screws

Nut driver and philips screwdriver.

Parts Used:

Water Inlet Valve

Edward from TUCKAHOE, NY
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

No water in

Pulled washer out. Found water inlet valve in lower left. Shut off power and water. Replaced valve with new.

Parts Used:

Water Inlet Valve

Everett from FREDERICKSBRG, VA
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Roller Broken on dishwasher

Popped out Old Roller, put in new one, pushing it together with a pair of pliers.

My only regret is that i didn't check the other side of the dishwasher... the other roller was broken also, and now i have to pay 5.95 shipping & handling for a .29 cent item

Check all your rollers before you buy just one!!!!!

Parts Used:

Dishwasher Dishrack Rollers and Axles

Sean from Cicero, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

Rollers worn out, top rack would not slide open or closed without wiggling around.

Removed rack, removed old roller pieces, installed new, replaced rack , and works as new now!!

Parts Used:

Dishwasher Dishrack Rollers and Axles

Darrell from DELANO, CA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Our dishwasher lower arm had become clogged

HAHA! The easiest repair we have ever done! Took it out of the box, snapped the old arm loose, put the new arm in and -- the dishwasher works like new! Thank you!

Parts Used: