FLCE7523AW1 Frigidaire Washer Dryer Combo - Instructions

Excellent!!! The parts fit perfectly, but most of all was the video that went through the repair step-by-step.

A local repairman quoted $198 for parts and another $150 for labor. Got the parts here for less that $26!!!!

The only issue (very minor) was the video called for a phillips head screwdriver to remove the front panel, and our dryer needed a squarehead driver. (If I was younger, I would have been able to see the problem).

But, I highly recommend Partselect!!!!

The part arrived just in the nick of time as my wife and daughter had strung up rope all over the family room to dry clothes. My son helped me lower the dryer to floor level ( this is a stackable washer/dryer set) Removed the top and front of cabinet. Removed the belt and popped out the drum. Took this opportunity to clean the amazing amount of lint from the blower housing and discharge hose ( it is my opinion that the accumulation of lint and the subsequent rise in operating temperature is the main cause of this bearing failure) Removed and replaced the rear bearing and greased it. Reassembled the drum,installed the belt and reassembled the cabinet. the only tools used were a screwdriver and a nut driver....and of course a vacuum cleaner. The rebuild kit is very complete and is the only way to go. Thanks for your fast delivery time, one more clothes line in the family room and I wouldn't be able to watch T.V.

We followed the video exactly. The video itself was simple and straight forward. Our model was a bit different than the video's example. The video's example had their spring action for the belt configured differently. When we finally figured out the difference, we were able to finish the job within minutes. The dryer now runs like new. We aren't mechanically inclined. That's why it took us so long. I still would recommend this company to anyone because it saved us time and money. The video really helps!

Taking apart cleaning putting back together I don't have any h-t lube so ill be doing it again. Thanks for the part ill be calling again!

Followed online video. All went smooth. Runs great!!!!!!!!!!!!!

Followed video instructions that were emailed by you.

I have a frigidaire dryer about 5 years old.

I first removed the top cover being careful to watch how the wires to the controls are connected. It is best to snap photos with your digital camera so you can remember how to reconnect the wires.

Pulling up on the drum, I lifted it out of the rear sleeve. Once out, you could easily see why it squealed. The metal bearing had groves on it where is made contact with the holder.

The difficult part of this was getting the 3 screws that hold the bearing to the drum off. The phillips screw head was easily marred if you don't have the proper screw driver bit. I think a better screw head would make the job easier.

After removal, the replacement was a snap. When everything was back together, the dryer sounded like new. The job took me about 2 hrs due to the hard part of removing the screws.

we removed the top of the dryer which was clipped on. then removed the front, including the door, being careful to unhook the electrical elements. then we removed the screws that attached the dryer drum to the back of the shaft. then we took the shaft out of the bracket. then we removed the plate from the back of the dryer that held the ball, the bearing and the bracket together. then we waited for parts and thanked God that the weather was fair so we could hang our clean clothes out!!! the parts came ahead of the rain so it was reverse order. then try the dryer!!!fantastic!! to qoute my kids "you rock"

I removed the panel's that enclosed the drum, removed the drum and cleaned all the lint around the drum, heat panel, drive motor, and switch's.
removed the old support bearing and grounding ball then applied grease into the new support hub and reinstalled the new hub and grounding ball and then reassembled the dryer. Runs like it was new.

after cutting the power, I used a putty knife to release the two holding clips ot remove the top,, 2 foward facing screws on either side of the front and two cap covered screws holding the bottom and unhooked the two electricial connections for the control panel and removed the front panel. Since this was a stack unit and in a closet most work had to be done from the front. By reaching inside to remove the belt from the motor,removing the drum was the easy part, to get to the bearing, but unfortunatly I had to remove the dryer from the closet to replace the back bearing clip and ball. After that replacing the bearing bracket and housing it was a breeze. Getting the unit back in the closet was a slight struggle, but it all worked out for the best got a chance to cleas behind the dryer, and the repaire was successful, phew.

Taking off front of and top of dryer and panels on the back. Releasing the belt and taking out the tube un screwing the two pieces off the back of the machine putting new ones in and putting belt back around drum and setting drum in. Then holding drum while the front is put back on then attach top and a couple panels on the back.

removed top and front of machine. removed drum. replaced shaft, bearing bracket, and support bearing from inside. replaced grrounding ball and clip from outside. reassemble.
this should be available as a kit, and should include high temp grease to put in bearing bracket

remove top lid (snaps and remove ground wire), remove front, 2 Phillips screw; remove nylon stop (Phillips screw) remove belt from motor (access plate 2 Phillips screws). Lift back of drum from pivot, remove from cabinet. check heating element for distorted or damage coils. Straighten or replace. clean felt surface and install new felt with glue. install new sliders in drum. assemble, rotate, listen for scraping. there should be no scraping sound when rotated. scraping can be from the heating element being distorted from lack of air flow because the drum stalled. If not fixed the heating element will be damaged when powered

Ordered the part from PartSelect.com. It came in a couple of days, which was nice. My wife was all over me to fix the dryer, or buy a new one. Needless to say, I didn't think the old one was done. The bearing assembly had an instructional video. This provided easy to follow instructions, and simple advice even I could follow. Everything went well, and the dryer is now quietly running as good as new. Awesome website, and the customer service is excellant too. WE use PartSelect.com at work all the time. Im a property manager, and the parts and advice save us thousands every year. Thanks guys!

The consensus seemed to be that the loud squealing was most likely the rear drum bearing needing to be replaced. Although the repair went very well (great video!), it did not fix the problem. BEFORE you go the route of replacing the rear bearing, first pop up the top and see if a little piece of plastic that is attached to the top middle of the front panel by a screw is rubbing against the drum (you have to have a load going). I removed this part (I could not find it listed on any parts list) and the squealing stopped. I have no idea what the purpose of this part is, except for maybe keeping the drum from dropping too far down if the load is really unbalanced. This plastic part is on the dryer that has the controls on the front (it has the ability to be stackable) and might not be on the other unit that has the controls on the top back. If anyone has posted this as a possible cause of the squealing, I haven't seen it.