Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Bearing Bracket Worn Out
Took off front panel, removed drum and replaced parts listed. A bit tricky to keep small parts in place. However, masking tape helped. Best of all was the online diagram of how the parts were assembled. In addition, taking step by step phone pixs aided in replacing parts since there was some down time between diagnosis and installation.
my motor was making noise i tried to replace the motor but could not get the blower wheel off the motor so i had to buy a blower and housing assy. also... now it works great...
Dryer door would not close, part had broke and fallen in. Once part was received it took less than an minute to put the new one in and I was back in business.
thanks for making it easy to find the part needed. and the delivery was fast!
unplug dryer. lift the top of the dryer up and back. Take the screws out holding the front panel on. One on each side. Disconnect wires from door open stop switch and take front panel off. Remove drive belt from around pulleys and lift drum up and forward out the front of the dryer. I had to replace the plastic and metal holder and the grounding ball also. Remove the shaft from the drum and put he new one on. Put the drum back in, wrap the belt around the drum and set drum in plastic holder. Then just reverse your steps. Fairly easy.
1. Released the front latches under the dryer top and flipped it up. 2. Removed two screws holding the dryer front in place and flipped it down. 3. Tore off old drum glide and lower seal. 4. removed most of the remaining fuzz with sandpaper. 5. Glued the new seals in place. 6. Put everything back together.
All in all, about 30 minutes of effort. I managed to come away with only minor cuts and scrapes.
Like the review of the guy who said "no story to tell. received knob and popped it on." I did not realize when I spoke to the Fridgedaire 1-800 number that I needed the model number; even though, I had the part number of the knob. When I came across your website, I entered the part number which was on the back of the knob and your website brought up the correct item I needed. I had seen the part on another website and your pricing was more than half off their price. Plus you shipped it directly to me two days later.
Used nut driver to remove screw and cover from dryer cord terminal block, used screw driver to remove two screws securing old terminal block, cut dammaged wire and stripped wire back and crimped on new terminal connecter, replaced old terminal block with new one, replaced two screws, installed new cord, and replaced cover plate and screw.
Vibration and Low Pitched Grinding Noise Developed as Dryer Heated Up.
**I'd already installed a new rear drum bearing assembly (very simple) and the issue continued. Further testing (running unit with the drum removed) indicated the blower assembly and/or motor was the source as the issue only occurred when the unit was under load. I ordered both parts as there was simply no way the original blower assembly was coming off the original motor.** Disconnected Power. Removed Top and Front of Dryer. Removed Drum. Disconnected Wiring Harness at Motor. Disconnected Blower Housing Temperature Sensor. Pried Open Clip Holding Motor to Mounting Bracket. Removed All Other Mounting Hardware. Removed Original Motor and Blower Assembly. Mated New Blower Housing to New Motor. Mated Assembly to Mounting Bracket. Reinstalled Clip Holding Motor to Mounting Bracket. Reconnected Wiring Harness at Motor. Reconnected Temperature Sensor to Blower Housing. Installed All Other Mounting Hardware. Reconnected Power. Checked Assembly Alignment. No Issues Noted. Disconnected Power. Reinstalled Drum and Front of Dryer. Reconnected Power. Checked Assembly Alignment While Under Load. No Issues Noted. Reinstalled Top of Dryer. Issue is Resolved. ** Thoroughly cleaned entire unit including under the baffle located at the rear of the drum. Amazing amount of baked on lint located there. Checked heating element (no issues) and cleaned lint trap assembly in door of unit. Another area with an amazing amount of baked on lint. Total for all parts needed was $236.91. Total time needed was about 3 hours. Parts arrived within one day of order. Unit operates 'as-new'.**
Rear plastic drum support bearing got worn making the shaft come in contact with the metal bearing bracket. That contact created a groove overtime and eventually snapped the shaft tip off.
Cut power off. Remove all the screws from the front panel. (where the controls are) working from the bottom to the top. Insert putty knife between the dryer and the control panel and push down to release. Carefully disconnect the wire harness. You will find 2 screws at the bottom and 4 on top holding the dryer door. Remove and expose the drum. Remove the drive belt Remove the drum. You need a 5/16 nut drive to remove the bearing bracket and an extra set of hands to hold the support from the back. Re-install the parts. I used bearing grease to make it run smoother Attach the new shaft to the drum and reinstall the drum (its best done with help)
Re install everything back again. And you are done
The dyer functioned fine, but was not producing any heat.
The repair was a bit more simple that what I had read here earlier, to see if I could handle it or I would have to call someone. The biggest relief was that I didn't have to remove any of the connectors from the control panel. Only 4 total connectors were removed at the Heating Element itself. Here's the steps I performed: 1) Pop the top off by prying the lid to release the 2 front clips and lift the top all the way up (like the hood of a car). Rest this against a door or wall. 2) Remove the rear access panel (2 phillips screws) on the bottom left of the unit. Remove the tension from the dryer belt and take it off the pully. 3) Go back to the front and remove (4 allen heads) from the back of the dryer drum. The drum should now have some play. 4) remove a plastic retainer that stops the drum from being lifted out. Now you should be able to lift out the drum. There is a ball & socket fitting that needs to come apart. This can be done by sharply lifting straight up. This gives you access to the heating element and you should be able to see where the coil has burned, thus opening the circuit. 5) remove (4 phillips screws) from the back panel of the dryer. Remove two pairs of connectors that attach to the heating element. Now it's out and you can begin the swap of the new element and reverse this process to put it back together. If I had to do this again, it would take less approx 30 minutes.
First I unplugged the dryer. I removed the 3 knobs on the front control panel as well as the 6 screws on the back. The start switch easily removes by turning it 45 degrees and pulls out. I used a pair of needle nose pliers to pull the two connectors loose from the old switch. (They are color coded wires, 1 brown and 1 gray. The switch is marked with the numbers 1 and 2 on the connectors so remember which one goes where) Then i hooked up the new switch in reverse order and was back in business in about 5 minutes.
The repair went very smoothly. I'm a woman in my mid 20's and was prepared to buy a new dryer but I saw the part online for a very reasonable price and the video instructions were extremely helpful. I was able to fix the dryer quickly and cost effectively AND the part arrived in only 2 days! It all worked out very well.
After the part arrived, I located a pair of needle nose pliers. Then removed the broken one and inserted the new one. It was very easy. I also noted that the new part was of a better design than the original. It should not need further attention.