EW26SS65GS0 Electrolux Refrigerator - Instructions

very easy to install...shipping was really fast...i would order to this website again....

I removed the Fresh Zone drawers from the refrigerator as well as the broken clip slide. I snapped the new clip-slide in place and checked drawer slide function. Then, I put the drawers back into the fridge. Voila! In less than 15 minutes the repair was fixed without any tools.

removed rear cover, removed screws, diconnected water line connections, cut off old water line connection, installed new compression water line connection, replace screws in water line housing, replace rear cover.

worked fine

Pulling the old seal was the easy part. The problem became dificult when I opened the seal package. Either Part Select or UPS had folded the seal in half. Witch caused the wire inside the seal to become crimped up. I used a pair of pliers "carefully" to straighten the wire as best I could. Luckly it worked, after pressing it firmly all the way aroud about 5 or 6 times. I'll still keep an eye on it for the next couple of weeks.

loosen 2 screws
unplug connector
remove
replug
replace
tighten 2 screws
done

The parts supplied were made to fit. The hardest part was getting the original broken tabs out of the internal walls of the fridge with out damaging the internal insulation. I punched the center locking pin through completely, dug out the broken tabs and then reached into the hole with a dental pick and pulled out the center pin. The new parts fit perfectly and with a plastic mallet, tapped the new locking pin into place.

removed fan unit from frig and installed new motor and then replaced back in frig. No tools needed. need to unplug unit and take apart and put new motor in the unit and then plug back in.

The site offers a video for this part which worked perfectly. In addition to replacing the part, since the cardboard panel was off, we also cleaned all the dust off of the coils which someone recommended to do annually.

Took the ice storage bin out. Took the unit apart,and disamble the augar unit. Ordered parts from manufacture, which arrived in two days. As soon as I got the parts, I reassambled it. Work perfect. Good job!

We followed the video instructions and it went fairly smooth. After turning off the water at the street we found that the faucet at the wall had it's own "on/off" valve. When finished, we turned on the power and heard the gears going through their revolutions, but no ice was made. We waited 24 hours and still no ice. I removed the cover on the ice maker and adjusted the amount of water to see if that was malfunctioning. Still no ice was created. Waited another 24 hours - nothing. Waited another 24 hours (the site said that sometimes the ice maker would take time to reset itself) - nothing. Then on the fourth day after changing out the triple water valve we heard water being dispensed and later that day it put out the first ice in weeks. Another hour later another batch of ice cubes were ready and deposited into the bin. Since that time, we have had a full bin. I moved the set screw back to it's original setting because a little too much water was being delivered. The cubes weren't separating to individual cubes. That cleared up the problem. This was easily completed - we recommend others do their own work. Just be patient for the system to reset itself.

I had removed the housing that the drum was in and taken the screws out to get to the broken drum. I removed it there was a set of 6 blades that crushed the ice that had to go back on the same order when I removed these I put them on a piece of wire in the order they came off (so I would get them back I the correct order). Then I reversed the order and reassembled it in the opposite direction . It was fairly easy to do. I'm a 68 year old disabled woman so if I could do it I'm sure you could to. Good luck. It cost me $14.00 if I had bought the whole assembly it would have been $150.00. So it was well worth my time and effort.

The most difficult task for me was getting old gasket out. I did call for repair help. The service person was most helpful. After almost giving up, one more tug and the gasket started coming out. Next step was cleaning the area. Aligning the gasket correctly made installation easier. I realized right away that I needed to start in a corner. The gasket went in without a hitch. My freezer is like new again. Next installment will be the refrigerator.

I followed the video tutorial published here. The step I altered was setting the shrink wrap; I did not have a heat gun to safely shrink it, so I folded it tightly onto itself and wrapped it in electrical tape. No more frost buildup.

Twisted replacement bulb into place easily. Let there be light!

Removed the plastic water tubes cover with a nut driver. Disconnected water hoses. Dropped control box assembly with nut driver. Removed old filter base with phillips screwdriver. Assembly opposite.