ESS341 Caloric Range - Instructions

It was simple. I flipped the circuit breaker just in case, and then unscrewed the bracket for the old heatng element. Disconnected the two plugs, connected the plugs for the new element, and screwed the new bracket back in.
The saleslady assured me when I was purchasing it from PartSelect that it was pretty easy. That gave me the confidence, and she was telling the truth. I will purchase again from Part Select....although I hope I won't have to do so for a while.

had to slide the range out from the wall and pull the electrical plug, then using a nut driver ,I removed 9 screws from the back panel and removed the back panel to expose the bake element wiring, had to remove the three wires connecting the power cord to the range terminals a/c the back panel would not fully come off with these wires connected. i then pulled the 2 stake eyes from the element, unscrewed the 2 screws
securing the bake element from inside the stove and removed the element, re-installed the new element and screwed into place, attached the
stake eyes on the rear of the element and re-attached the power cord, put the back cover back on and plugged the range in., tested and the range functioned as intended.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Plug the wires onto the new bake element and re-screw back into place.

I reoved old drip pans and installed new ones. Very easy, they look great!

First, I unplugged the power cord from the receptacle. I then removed two philiphead screws that hold the element in place. I the pulled the element out about an inch and a half . I then disconnected the the two wires from the element. The I connected the replacement element and resecured it with the two mounting screws. I assured everything was correct and then I plugged in the power cord and turned the oven on low heat to give it a test. Everything workout just great. The part was just what I needed.

I turned off the breaker and unscrewed the element. Removed the plug connection and once I got the correct part, we plugged it in, screwed it back into the oven wall and done! I am a single female and was able to replace the heating element in a short amount of time with assistance from my 16 year old son!! I was very surprised at how easy it was to repair. The key is to get the correct part the 1st time!

removed the plug that had burned up on one of the top burners, replaced it with a new plug purchased from parts select., it was quite easy ,I unpluged stove and raise the top exposing wiring for the burners cut the old plug wiring and connected the wires for the new plug with connectors and shrink tubing supplied in the repair kit easy and quick repair

Very simple fix. I pulled the stove away from the wall and unplugged from outlet. Open the oven door and remove the oven racks. I used a phillips screw driver to remove the 2 screws holding the element and then pulled out. There were 2 wires attached to the element, those just pull off. Just reverse the process with the new element and you are good to go.

Lift burners out of plug discard old drip pans replace new drip pans into plugs and done .

Oven was missing the broiler element when I moved in so the connector/wires to plug the broiler were no longer visable in the main part of the oven (otherwise the repair would take 2 minutes). Moved oven away from wall and unplugged. Unscrewed sheet metal on the back of oven and found the broiler wires (the only two NOT connected to something). Fed the wires back into the oven and plugged in the broiler. Attached the broilers to the top hooks. Put sheet metal back on. Everything worked fine. I wouldn't say I know much about fixing things, but this was a very straight-forward job.

Although this was not a repair I wanted to let you know your service was outstanding and the price quite reasonable. I am very happy to finally have a much needed second rack in my oven that was not there when I purchased my home. Thank You

take out the old put in the new

Removed old drip bowls, removed burners installed new drip bowls,installed burners. They fit perfect and I received them two days after ordering.

Pulled the old one out and plugged the new one in. It was that simple!

Removed 2 screws from mounting plate in base element.

Disconnected 2 wires from bake element.

Installed new bake element in reverse.