EKT-396 Caloric Microwave Oven Combo - Instructions

had to slide the range out from the wall and pull the electrical plug, then using a nut driver ,I removed 9 screws from the back panel and removed the back panel to expose the bake element wiring, had to remove the three wires connecting the power cord to the range terminals a/c the back panel would not fully come off with these wires connected. i then pulled the 2 stake eyes from the element, unscrewed the 2 screws
securing the bake element from inside the stove and removed the element, re-installed the new element and screwed into place, attached the
stake eyes on the rear of the element and re-attached the power cord, put the back cover back on and plugged the range in., tested and the range functioned as intended.

First, I unplugged the power cord from the receptacle. I then removed two philiphead screws that hold the element in place. I the pulled the element out about an inch and a half . I then disconnected the the two wires from the element. The I connected the replacement element and resecured it with the two mounting screws. I assured everything was correct and then I plugged in the power cord and turned the oven on low heat to give it a test. Everything workout just great. The part was just what I needed.

Although this was not a repair I wanted to let you know your service was outstanding and the price quite reasonable. I am very happy to finally have a much needed second rack in my oven that was not there when I purchased my home. Thank You

Very simple fix. I pulled the stove away from the wall and unplugged from outlet. Open the oven door and remove the oven racks. I used a phillips screw driver to remove the 2 screws holding the element and then pulled out. There were 2 wires attached to the element, those just pull off. Just reverse the process with the new element and you are good to go.

removed the plug that had burned up on one of the top burners, replaced it with a new plug purchased from parts select., it was quite easy ,I unpluged stove and raise the top exposing wiring for the burners cut the old plug wiring and connected the wires for the new plug with connectors and shrink tubing supplied in the repair kit easy and quick repair

I first killed the power to the oven by switching off the circuit breaker and then unplugging it from the wall. With the oven pulled out, I removed the back cover panel to disconnect the lower (bake) element power leads from the broken element. I removed the two screws on the metal plate that attached the element unit to the oven and removed the whole bake element assembly from the oven. I then inserted the new element assembly into the oven and reattached the screws. The next step was to reattach the power leads to the new element. It was then time to put the back cover panel back on and plug the oven back in. I then pushed the oven back into place and switched the circuit breaker back on. Finally, I tested the new element to see if it operated properly by setting a temperature and observed the temperature on a separate oven thermometer used for baking. Your exploded views of the oven helped me plan and execute this repair. Good feature that would be even better if the resolution was a bit better.

No problem Took off old ones and replaced with new.

Removed two screws-put burner in-pit screws back in! Turned over on and it worked!!!

Switch off the breaker or unplug.
The screws were in tight so make sure your philips bite is new so you do not strip.
Pulled the element out and held the wires in place with a clothes pin so not to slip back in the stove.
Connect and cooked up pizza for dinner.
Very easy

Pulled the old one out and plugged the new one in. It was that simple!

I replaced the large capacitor (.95 uf). Much of the shell (casing) has to be removed and the capacitor is hard to get to. It is housed in a very inconvenient place. Because of the unfamiliarity of how to access the capacitor it took about an hour to get to it. After receiving the new capacitor it only took about half an hour to install it, re-assemble the microwave, and re-install under the cabinet. Of course a new fuse was required.

My Maytag Microwave UMC5100AD was suddenly broken in 1 second when I heated food last time. Then no clock, etc, seem the fuse broken. to fix it, the most difficult part was how to remove it from the wall trim. Finally got it out. Then went HomeDepot to get the same fuse, replaced and used it, burned again. Then I searched online and ppl said the capacitor might be the one. I took it out and measured it, yeah it indeed was a problem since it's not open. Then I order the capacitor from PartSelect about $32. After 3 days I got it and installed it. Done. Sure need to put the Microwave back to wall trim. That's it. Saved about $500 buck if I buy a new one plus labor to install it. Thanks

Replace the capacitor and the fuse. Then it works again. Part arrived in an open plastic bag with scratch. It looked like a returned part, but it works fine.

Removed 2 screws from mounting plate in base element.

Disconnected 2 wires from bake element.

Installed new bake element in reverse.

I followed the instructions provided.