This manufacturer-certified drip bowl is also known as a drip pan, and it is designed for use with cooktops and ranges. It sits below 8-inch burner elements and catches drips and spills from the cookware on the burner. The diameter of the drip bowl is approximately 10 inches. This replacement might appear slightly different, but it will f...Read moreit your appliance.
You will need no tools to complete this repair. Simply remove the burner element, remove the old bowl, line up the hole on the new bowl with the terminal block and drop it into place. Make sure the bowl is flat before reinstalling the element. While you have the element out you should inspect the terminals for corrosion, damage, or discolouration. If you notice any of those things you should also replace the element and terminal block. You will need to replace your drip bowl if it is lost, damaged, or can no longer be cleaned. This replacement part is sold individually. To extend the life of your new drip bowl we recommend you clean it regularly with soap and water. We recommend only using the recommended drip bowl for your appliance; generic versions will not fit properly which could affect the performance of your elements and cause long-term damage.
The surface burner plug-in block kit features a newer-style terminal block. This kit is designed for use with ranges and cooktops. This terminal block is how the coil element on your stove connects to the inner wiring of your appliance. Without this connection your burner element would not get the electrical current it needs to heat up. W...Read morehen your element will not heat at all, or if it is not heating properly it is likely an issue with the terminal block. You need to remove the element to replace this part. While you have the element out, inspect the element and the terminal for any corrosion, arcing, or discoloration. If you notice any damage to the element or the terminals we recommend you replace this part as well. This kit includes two metal brackets, two pre-crimped high-temperature wire leads, two ceramic wire nuts, two heat-shrinking insulators, and a mounting screw. Before you begin this repair, make sure you have unplugged your appliance.
Please note: This is a substitute from the original part. It may physically look different, but will still function the same. This bake element is found on the bottom of the oven.
This is a surface element for the stove top on your range. It supplies heat to the top of the range cooking area. This model is 2100 watts and is eight inches in diameter. It has looped terminal ends, and five turns. The most common reason for needing to replace this part is if your current element is not retaining heat. The first step to...Read more this repair is to make sure the burner control is set to off, and that the element is cool to the touch.
This microwave fuse is just over an inch in length. It has a white ceramic center, and metal on either end. This is a twenty amp 250-volt fuse, and is used to power your microwave. If your microwave will not heat properly, will not turn on, or the touch pad becomes unresponsive, there could be a faulty fuse which should be replaced. Remem...Read moreber, since this part contains an electrical charge, before you replace the fuse from your microwave, make sure that the power is disconnected from the unit. This part is sold individually.
NOTE: Make sure your microwave is unplugged, and your capacitor is discharged before you begin this repair. A capacitor stores large amounts of electricity even after your microwave is unplugged.
Get your cooktop working like new with this 6-inch coil burner. It heats up with 1500 watts of power—great for boiling, simmering, or everyday cooking. Easy to install with looped ends that connect quickly, and it even has a sleek black center for a polished look. If your old burner stopped heating, this is a simple fix to get back to cooking.
This oven light assembly is a little over four inches long and comes with the lens and 660-watt light bulb. Make sure your appliance is unplugged or circuit breaker is off before installing this new part. It is located inside the oven and may need to be replaced if the socket has failed, causing the light to not come on inside the oven. I...Read moret may also need to be replaced if you notice that the glass is broken and the whole assembly needs to be replaced. The part is located in the upper right hand side of the oven. To reach the bulb you will need to open the oven door and remove the upper rack.
The hinge kit, or oven door hinge, is used in ranges and wall ovens. The hinge attaches to the right side of the door and controls how fast the door opens. At a specific angle, it allows the door to remain open. If you are having trouble opening and closing your door, or it does not close at all, replacing the hinge could solve your probl...Read moreem. The hinge is made from metal and the kit comes with the hardware needed for this installation. You will need a screwdriver to perform this repair. *Please note: This part is only for the right side of your appliance. The left side is sold separately.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The Baking element in the bottom of the stove apparently shorted out and partially melted
59 of 61 peoplefound this instruction helpful.
Timothy from Salem, OR
Easy
15 - 30 mins
Pliers
First I turned off the circuit breaker on the house electricity panel. I removed the two screws that held the element in place in the oven. There were two wires connected to the element by spade plugs that were free floating in a fiberglass pad. I reconnected the spade plugs and put the element back in place and put back in the two sc
... Read morerews. This procedure had I known what I was doing could have been done with the stove in place and would take no more than 5 to 10 minutes. Having no experience at this, I had pulled the stove out into the room and also removed the back cover which turned out to be unnecessary. I put everything back in place and held my breath and turned on the circuit breaker. Voila! It worked!
Read less
Was this helpful?
Thank you for voting!
Blows main fuse when the microwave generator start, (cooking function).
39 of 48 peoplefound this instruction helpful.
Jay from Edwardsville, IL
A Bit Difficult
30 - 60 mins
Pliers, Screw drivers
Remove microwave from oven cabinet. remove cover and check main fuse with ohm meter. Tried fuse, it does not blow untill cooking starts. Check capacitor with ohm meter, after properly performing capacitor dischagre procedure. Order new capacitor, simple installation. another new fuse and all is good and cooking again.
First I removed upper front grill by removing two Philips head screws on top and pulling off. This exposed the Philips head screw which holds control panel in place. After removing screw I pushed up on panel and it came off to expose fuse. With needle nose pliers I removed old fuse and again with pliers held new fuse in position. With th
... Read moree help of a bladed screwdriver, I pushed new fuse into holder, then replaced panel, screw and grill. This took less than 15 minutes even as one of the wires on control panel pulled out of connection and took some time to locate where to reconnect, otherwise was an easy fix .