Quick Question!

Have you ever purchased from PartSelect.com before?

Models > E23CS78EPS1 > Instructions

E23CS78EPS1 Electrolux Refrigerator - Instructions

All installation instructions for E23CS78EPS1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the E23CS78EPS1
61-75 of 457
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Water Was Dripping From Base And I Had No Ice Being Made Or Water In The Door.

  • Customer: john from mckees rocks, PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 9 of 13 people found this instruction helpful
Removed the plastic water tubes cover with a nut driver. Disconnected water hoses. Dropped control box assembly with nut driver. Removed old filter base with phillips screwdriver. Assembly opposite.

Plastic water actuator snapped in two.

  • Customer: Alexander from Santa Monica, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 10 people found this instruction helpful
1. Removed exposed screws
2. Removed face plate
3. Disconected wire from switches on face plate
4. Removed screws holding ice/water dispenser
5. Removed screws holding actuator in place
6. Removed wireconnection on actuator (lighted)
7. Replaced broken actuator w/new
8. Replaced all parts in reverse order of removal
9. $300 service call costs me $75 and and 30 minutes of my time. I will always try to fix appliances with the help of PartSelect before calling for service. Thank you!!

Snapping noise from bottom of refridgerator door bottom hinge.

  • Customer: Dennis from Crossville, TN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 7 of 8 people found this instruction helpful
First I looked up and called Fridgedaire. They were absolutely no help at all. No diagrams and no intelligent help.
When I found your site there was an IPB (Illustrated Parts Breakdown) diagram that helped me find the parts that I suspected as being the problem. When I found them and added them to my cart I found several comments from people who had the same problem and the same remedy to the problem. I ordered the parts, I could have got away with just replacing the door closure bearing, but I figured that the prudent thing to do while ordering parts and disassembling the door was to replace both.
I was extremley pleased with the parts service as within three days of ordering the parts they were at my home and the repair was completed.
The repair was very easy. Removed the items from the door storage, removed the upper hinge pulled the door, removed the door stop, replaced the door closure bearing reinstalled the pieces and then reinstalled the door. Piece of cake. Spent more time getting the tools together and emptying the items stored on the door then replacing the parts.

Frost build up on evaporator

  • Customer: B J from Dillingham, AK
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 11 of 20 people found this instruction helpful
Remove the bottom freezer drawer. Remove back metal evaporator panel. Wire in new defrost terminationT-stat. Reassemble evap panel. Good to go.

There was a horrendous popping noise when I opened the refrigerator door.

  • Customer: Weston from Anchorage, AK
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 7 of 8 people found this instruction helpful
First I cleaned out the side door then, removed the three screws on top of the door. Lifted the door off and set it carefully on a kitchen mat.

I had to use the pliers to remove the existing bearing hinge as it had disintegrated in the door. Once it was out the new hinge slid right into place and I reinstalled the door. I had help with the door. It’s much easier with two people to get proper alignment and to hold it in place while you reattach the screws.

I would have to say the hardest part of this repair was cleaning out the refrigerator.

Ice maker malfunctioned

  • Customer: Myron from Tumwater, WA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
  • 8 of 11 people found this instruction helpful
We followed the video instructions and it went fairly smooth. After turning off the water at the street we found that the faucet at the wall had it's own "on/off" valve. When finished, we turned on the power and heard the gears going through their revolutions, but no ice was made. We waited 24 hours and still no ice. I removed the cover on the ice maker and adjusted the amount of water to see if that was malfunctioning. Still no ice was created. Waited another 24 hours - nothing. Waited another 24 hours (the site said that sometimes the ice maker would take time to reset itself) - nothing. Then on the fourth day after changing out the triple water valve we heard water being dispensed and later that day it put out the first ice in weeks. Another hour later another batch of ice cubes were ready and deposited into the bin. Since that time, we have had a full bin. I moved the set screw back to it's original setting because a little too much water was being delivered. The cubes weren't separating to individual cubes. That cleared up the problem. This was easily completed - we recommend others do their own work. Just be patient for the system to reset itself.

Ice maker quit working & was over flowing

  • Customer: kenneth from lincoln, NE
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 9 people found this instruction helpful
We had to unhook & remove icemaker several times, thaw it out & reinstall, it would work for a day or two then overflow. Bought the new ice marker, replace it and it works great....

Rust had corroded Front Plate and Drive Blade

  • Customer: Calvin from Massillon, OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 7 of 11 people found this instruction helpful
Installation was completed by following the online Parts diagram. Had to completely remove all parts, including the blades in ice crusher, and re-assemble. Glad the online diagram was clear and easy to read.

My ice auger would not work.

  • Customer: Dennis from Point Roberts, WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 7 of 11 people found this instruction helpful
After taking the complete motor, tray, icemaker, etc out and finding no problem, I then finally checked for power at the connector at the top of the icemaker. I concluded that there was no pwoer going to the motor. I then removed the circiut board and found the relay for the auger was not working. Putting the new board in took 10-15 min. and then the auger started to work.

door wouldn't close by itself anymore and there was black stuff at the bottom of the door

  • Customer: Karla from Grantsville, UT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench (Adjustable)
  • 6 of 8 people found this instruction helpful
Emptied the shelves off door and pulled door off fridge swet on counter and took out old plug and put new one on.

Support stude for both vegetable crispers broken off

  • Customer: RANDY from NORTH CHARLESTON, SC
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 5 of 5 people found this instruction helpful
Support studs have an expansion fitting - center post has to be pushed through to allow expansion joint to collapse for removal. After installation, this post can be pushed in or pulled out to secure the stud and be the proper length to hold the bins.

None of this was obvious - an online tip from another member was invaluable.

door woulg clunk and drop

  • Customer: bruce from eldridge, IA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 5 of 6 people found this instruction helpful
took door off(very easy two bolts on top)lift door replace parts

Bearing broke

  • Customer: Walter from Hamilton, OH
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 5 of 6 people found this instruction helpful
Took off Door on Refr. and unscrewed Doorstop,
removed doorstop with broken Bearing and replaced with new Parts. Took about 20 Minutes
including reattaching Door. A 10 year old can do it.

some parts in the ice container had rusted

  • Customer: John from Santa Monica, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 8 of 15 people found this instruction helpful
pulled out the old assy and replace with the new one.

broken shelf support

  • Customer: Richard from West Seneca, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 5 of 6 people found this instruction helpful
I broke off remainder of clip, and used phillip
screwdriver and pushed pin into wall. I lined up new support and pushed in peg to secure
All Instructions for the E23CS78EPS1
61-75 of 457