DW1000W Jenn-Air Dishwasher - Instructions

This was really easy. I just took out the two screws securing the unit to the counter top and slid it out about 6 inches. Broken plastic spring linkage was obvious and easily accessible. I didn't know there was one on each side, I would probably have went ahead and ordered both and replaced them at the same time.

Removed the 6 screws holding the pump and motor assy. Disconnected the two hoses and wiring connector. Removed the motor and pump, removed the pump parts to get down to the impeller. Removed the old impeller (one screw) and installed the new impeller. Put every thing back together and it worked fine. Every one is happy!

First, I removed the screws that hold the interior part of the door in place. Next, I removed the two screws that covers the interior parts of the latch release in place. Then, I removed the broken latch, put in the new one and attached the spring. I put the pieces back in place, and the two screws back in. Finally, I screwed the door panel back together.

1) Emptied Dishwasher (roll-around model)
2) Tipped it onto its back
3) Removed Toe Kick (2 screws) and Bottom Cover (4 screws) (screw driver)
4) Opened Door to access side panel (careful not to let it drop on my fingers)
5) Using Torx driver, removed two screws holding side panel on. This makes it easier to access the linkage and spring.
6) Removed broken link
7) Installed new link and spring noting the spring direction from the spring on the other side of the door.
8) Pulled spring over the bottom rail bracket with pliers.
9) Reinstalled panels in the reverse order.

The problem was the rubber end on the upper shower head pipe at the pump. Not to hard . Slide dishwaser half way ouy the ptpe is on the right side.The bottom end is is just a clamp the top drops in from the top, inside there is a nut above the upper shower head. You can unsrew the nut with your fingers, it is right above the upper shower head.There it a washer at the top of the pipe that should be replaced that doesnot come with the pipe

Turned off power. Removed lower, two panels. Turned power back on and started dishwasher. Saw leak from 7' drain hose. Turned off power, disconnected hose, ordered new hose, installed on washer and routed back to garbage disposal. Turned on power, checked for leaks (none) and replaced 2 front, lower panels.

first I turned off the water to the dishwasher, and turned the power off for the dishwasher.
removed the 4 screws from bottom panel
then removed the 2 screws from the bottom of the counter,
at this point I could pull the dishwasher out. then figured out where the part went and attached.
pushed the dishwasher back and lined up the holes under the counter, put those in first, the put the bottom panel back on, turned the water back on, and flipped the breaker switch.
Reading the other stories really did help me get some idea of what needed to be done

I removed the old door gasket and thoroughly cleaned the track. I placed the new door gasket in place- no problems.
I had to remove the 7 screws from around the door to access the old, crumbled gasket. This was accessed by removing 2 screws with a socket wrench. The old gasket pulled out and the new one slipped right in.
No more leaks!

Attaching the part to the door only took a few minutes but getting the dishwasher out over the hardwood floor that was installed after the appliance was put in was a pain. I had to remove a piece of the hardwood floor and use some technique to get it out of the opening so that the springs were visable. There is no problem after that. I would recommend using work gloves to stretch the spring over the retaining notch on the door so that you don't pinch your hand.

I first removed both lower front shields,(4 screws)
I then shut off water supply to inlet valve from hot water supply. I removed the water hose from inlet valve,two electrical terminals,( I put tape on right side terminal and lettered with an R as not to mix up the two terminals)removed the hose clamp,removed valve from frame.I reinstalled in reverse procedure.I turned the water back on and checked for leaks.I started the normal cycle and water flowed into the dishwasher as designed.

I first removed the bottom access panel and 2 upper screws holding the dishwasher to the counter. Be sure to remove the standing water in the bottom tray. I pulled the chassis far enough forward to reach where the top shower hose attaches ( the supply line and wire had enough slack to move the chassis ). Not knowing how the rotating shower arm attached, I unscrewed the ribbed retaining ring above it, and found the whole assembly came loose - freeing the upper end of the shower hose. Put a shallow tray under the lower end of the shower hose to catch the remaining water and loosen the hose clamp to free the remaining end of the hose. Transfer the rubber washer at the top end and the hose clamp at the bottom, to the new hose and install. A quick repair, but one that shouldn't be needed on a 4 year old dishwasher.

Unscrewed the inside door panel. Removed the reservoir assembly. Disconnected the wax motor. Replaced it with the new motor. Replaced the new o-ring. Done. The hardest part was finding out why it was not working and how to fix it. Google for a long time in order to find some idea what to do. Then took the door apart to see the reservoir and the wax motor. After that, it was pretty easy. HTH

I opened the dishwasher door, then used the Torx bit to remove the screws all around the edges of the door, and removed the inner part of the door. Then I removed the long metal plate at the part of the door farthest front (with the door open) and the large black plastic housing. The metal plate then became a useful tool to brace at an angle between the door and the body of the dishwasher. This not only held the spring-loaded door down, it also held the inner part of the door up against the body of the dishwasher.
One nut held the latch assembly to the door; I removed it with the nut driver.
On the latch assembly, there are two small plastic catches that keep the latch from sliding out, I held those out of the way with a blade screwdriver and slid the latch out.
The new latch then snapped into place, and I assembled the door again in the reverse sequence of disassembly.

I followed instructions of others that were posted. Door seal was simply removing old seal, cleaning track and pushing new seal in,making sure it was even all around. Removing the door cover to get at the Dispenser grommet was simply removing all 7 hex nut screws. Had to go out and buy the proper hex nut screwdriver . I did not remove the wiring, just turned cover over to remove the two nuts holding the dispenser. The nut on the left was a little hard to get off, had to kind of force the socket onto the nut. Otherwise all went well and simply removed the old grommet and installed new one. Finding the right tools was the part that took the longest. I had hard water before putting in a water softener so that was probably hard on the seals plus the machine was an older model. No problems now and saved having someone come in and do a repair.

I simply connected the two hoses to the valve plugged in the two wires and it was working!