DBXR463EB2CC General Electric Dryer - Instructions

I narrowed the porblem down to the rotary start switch, which is located in the top panel. It takes a hex wrench to remove the four screws holding the fron top panel in place and of course the knobs had to be removed. The switch rotates about a wuarter of a turn to come out. Label and remove the three connectors (3). It took about a week to get the replacement part which was slightly different than the original part. The good thing is it had the three prongs like the old part.. I hooked the connectors in the same configuration as the old switch, plugged the power cord back in to test and it started right up.

Unscrewed three screws on back and removed the switch and inserted the new one. There are 3 wires that clamp on the switch. Remember to unplug before doing this.

Real easy and great people to work with. Much cheaper than a technician repair.

Jim

Unplugged the dryer. Took the four star screws out of the console top. Pull consoled forward. Removed the knob. Pull up the locking tap on the old timer and twisted the timer counter clockwise. Timer easily detached from its mounting plate. Changed one wire at a time from the old to the new timer. Replaced timer and knob and screws.
Works great.

The repair, from the time that the bulb burned out until it was replaced took about six months. I could have shortened the time if I had ordered the bulb sooner. It was difficult because I had to listen to a fair amount of nagging, which, thankfully, has now ceased. I also had to actually go online and finI opened the dryer door, reached in with my right hand (which happened to be holding the new bulb) and screwed the new bulb in. Tip: Screw it in counter-clock wise. This was not mentioned in the instructions. Come to think of it, no instructions were provided. The company might wish to correct that oversight.

I first throwed the breaker then I took the old bulb out. Put new bulb in. Turned the breaker back on.
It worked great

I replaced the old knob with a new one.

Unplug. Remove 3 knobs at front of panel. Remove 4 screws. Panel pulls forward. Remove green grounding wire to allow panel to come forward more. Pry up locking tab on switch. Turn switch to unlock from panel. Install new switch in reverse order of removal. Pull off each wire one at a time from old switch and attach to new switch. Reinstall panel and insert 4 screws. Done. My wife was so suprised that it actually worked and I fixed it in less than a day! Only took about 20 minutes. Thanks Part Select and the other repair stories that I read on your website.

Washer - remove 4 screws (phillips)on the back of the panel, slide it sidways slightly and pull forward to release. remove clip behind knob ( kinda like the clip on old car window handles) remove knob and dial. remove 1 nut on timer, rotate timer to release. installation is just as easy, but put clip onto knob first then just push onto dial shaft, it will click when on correct.

Dryer - remove 4 screws (phillips) on back of panel and remove same as washer. dryer switch will have a little cam lock on it just pull it off the plastic retainer and rotate switch. Remove wires one at a time and put on new switch so as not to wire wrong. reverse for re-assembly

Tried to replace with home-store bought 6w light. Looked the same, fit into socket, but didn't work. Actually exploded when I turned it on! Be sure to use OEM part like this one. Worked perfectly!

I moved the dryer away from the wall and unplugged the electrical cord. I unscrewed the 4 screws on the top of the dryer to gain access to the Dryer Rotary Start Switch. I pulled the part out of its set location and carefully removed the clip on wires. I then carefully attached the wires to the exact locations on the new part and put it back into the proper location. I installed the screws, plugged in the power cord and moved the dryer back to its location for operation. I turned the circuit breaker back on. I failed to mention that I turned that off first of all. I set the dryer control to dry and turned the Dryer Rotary Start Switch to on and it worked immediately. This took about 12 minutes totally from start to finish.
Thank you for being there.
Sincerely, John Pewters

Removed the 6 screws that held the top panel in place. there are only 3 wires, 2 that go together and 1 single wire.Uplug the dryer,twist out the old switch,twist in the new one, attatch the wires,replace the panel,BAM your done.And the best part of it all the part was right the first time.they make it so easy to get the right part the first time!

First unplug dryer to prevent electrical shock. To remove the front of the dryer, open the door in top left and top right corners is a machine screw. They can be removed with a Phillips screw driver. Lift the top slightly and let front fall forward about 6 inches, lift slightly. Two wire will be connected to the switch in the door. remove the wires and squeeze the tabs on both sides of the switch and push it out. Push new switch in to replace old switch and reassemble.

I took off the broken knob since it was already loose. Then I removed the new part from its wrapper and lined the bolt up the knob. Inserting and pushing until it felt like the knob had a firm grip the job was done.

I first unplugged the unit, opened the top, disconnected and took off the control panel, took off the front panel to determine the source of the squeaking noise coming from the Dryer. I saw that 3 of the 4 Front Drum Glides were gone and the drum had worn away significant amounts of plastic from the Top Bearing Assembly. I purchased the Top Bearing Assembly and a set of 4 Front Drum Glides. Disassembled the damaged parts and reassembled with the new replacement parts. The reassembly took less than 20 minutes. I plugged in the Dryer and viola! It works as good as new.

opened up the control cover, pulled off the 3 wires to the switch. unclipped the swutch from the panel and reinstalled the new exact replacemnt sww you sent