DRYER FRONT BEARING WHITE 2PK WE03X37318

Light Bulb

Michelle from STATHAM, GA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers

10 of 12 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Gas dryer only fired at the beginning of it's cycle

Be sure to segregate and label all screws.
Remove back and front of control panel.
Removed dryer top.
Removed dryer front/door panel.
Replaced slides. Due to discoloration it was hard to tell the white fr the green. Double checked partselect videos to be sure which was which.
Propped up drum with the dowel to allo ... Read more

Read less

Other Parts Used:

M - Series Secondary Coil - 2 Terminals

M-Series Primary Dual Coil Gas Valve

Robert from RIO RANCHO, NM
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Dryer was making loud noise

Upon receiving the parts, we went to the video repair instructions. We found these videos to be very well done and very helpful. It was great being able to pause the video at specific points until we were able to complete that step of the repair. All of the replacement parts fit correctly and there were no issues.

Other Parts Used:

Stephen from FISHERSVILLE, VA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

6 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

dryer had started making a squeaking noise that got progressively worse with each use

i ordered parts before taking the dryer apart, based on the symptoms others described so that i would have everything i needed. sure enough once i pulled the panels off, the drum slides and entire bearing were destroyed. i assume that happened with age, and ignoring the problem didn't help. by the time i replaced the parts I'm surprised t ... Read more

Read less

Other Parts Used:

timothy from BALTIMORE, MD
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Excessive Drum Noise While Drying Clothes

The PartSelect company's "how to" repair videos are OUTSTANDING. Thank you! The videos provided a comprehensive overview of what to expect in terms of clothes dryer disassembly, component replacement and reassembly. The videos were invaluable tutorials for prior-to-disassembly work.

I ordered all the following parts which I fel ... Read more

Read less

Other Parts Used:

Drive Belt

Rear Drum Bearing Kit

DENNIS from RALEIGH, NC
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Pliers, Screw drivers, Socket set

7 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Bearings completely worn out, including plastic.

Install would have been easier if part was
an exact
fit. Had to make do with part not fitting exact. Let's just say the dryer works but light won't line up.

Other Parts Used:

Light Bulb

Ruth from GRANITE CITY, IL
Difficulty Level:
Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

7 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Dryer was making a loud noise when running.

I am a 55 year old woman who likes to repair household items. I followed You Tube instructions and did it all by myself. A few screws to get the top off and a two more to remove the front piece. Trap duct assembly was cracked and falling apart. Pulling off the old was fairly easy. I watched the You Tube instructions on my Ipad so I co ... Read more

Read less

Other Parts Used:

Dryer Lint Chute Assembly

Robbin from COLUMBUS, OH
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Loud sqeeking.

I followed some simple instructions from GE. It was really easy and I even found some spare change inside the cabinet which my wife took off my hands. :/

Other Parts Used:

Drum Bearing Sleeve

Kevin from HENDERSON, NV
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

5 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Dryer making a loud squeaking noise and had a crack in housing that would catch clothing and twist it up into a ball.

The repair went very well, parts fit perfect. Now there isn't anymore complaints.

Other Parts Used:

Dryer Lint Chute Assembly

Drive Belt

Steven from GOSHEN, IN
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Dyer made a squealing/screeching noise

I have read other postings which describe most of the procedure very well, so I'm just going to add things that should be considered, which I have not read about here.
Removing the drum proved difficult due to the lack of room on the two sides.The vent blower motor bracket is at the front bottom of the dryer, and when the two screws ... Read more on either the left or right side are removed, the dryer sides spread more easily and allow the drum to be removed or re-installed more easily.
Next, the rear drum bearing I bought has a rubber o-ring which holds it in place. There is a good chance this o-ring will be hard and brittle after years of service, and will crumble when removed, in order to replace the bearing. I had to run to the local hardware store to get a new o-ring, and could only find one that did was not rated for high heat usage. I presumed once the drum is re-installed that the bearing can't dislodge even with a missing o-ring. I think it just holds the bearing in place while removing and re-installing the drum, but I cannot be certain about this.So if you plan to replace the rear drum bearing, make sure to also order the o-ring that holds it in place. It is doubtful you can re-use the old one depending on the age of your dryer.
Replacing the old white belt tensioning pulley requires the removal and re-installation of a "nut" that has no threads. It is forced on and off and not simple to re-install. The removal was easy simply by using a wrench to "unscrew" it counterclockwise. But re-installing it is another matter. It requires force to get it back onto the shaft. I saw a tip to use a 7/16" socket placed over the nut and hit with a hammer while bracing the bracket from the other side. I did this by used a smaller tool, linesman's pliers, which provided the force needed. Install it about 1/4" past the end of the bracket shaft. Careful, that nut has sharp edges and I ended up bleeding from that process. Three hands would help: one to brace the bracket, one to hold the nut and socket in place, and one to hammer. So good luck with that. Probably there is a smarter way to do this.
If you replace the old white plastic belt tensioning pulley with a new yellow one, it is not simple to understand how to re-install the belt properly. The videos do not do the trick adequately. I did find one on youtube where they removed the dryer side in order to show the belt installation and I had an "aha moment". Since you cannot see the belt, the pulleys, the motor, or anything else during installation, it is not a simple thing to do. Here are my tips: Before re-installing the drum, move the belt tensioning pulley bracket to the right (when facing the dryer front) and you will see a little spot where the bracket will stay to the right when engaged in this spot. Engage the bracket and then proceed to re-install the drum. That way, when you reach under the drum to set the belt properly on the pulleys, you won't have to engage the tensioning bracket without being able to see. Once the belt is in place, carefully remove the bracket from the right holding spot and allow it to move back to the left operating position. I used two hands and don't think I could have done it with one. When the belts are new, they can be naturally twisted and you have to be careful to install the belt with no twist. I had to do it twice to get it right. If someone can take up the top belt slack for you, it's easy to feel the belt underneath the drum and get any twists out.
Next, i had a hard time inserting the drum back into the dryer and finding the hole where the bearing inserts. The problem is, if you are not careful, it's easy to move, bend, or break the heater wires which surround the hole you need to locate blindly and slip the drum bearing into. I did bend those wires, but luckily not break them. In hindsight, applying some masking tape to the rear inside panel of the dryer right at the top, left and right of the drum BEFORE removing the drum would have made it much easier estimating the proper drum height while maneuvering the bearing into the rear hole. Then remove the masking tape when done.
I ordered a new top plastic front bearing that supports the drum in the front. Good thing I did because mine was split about 5" where one set of the green and white sliders install. I had one white "plastic" insert visible. The other one plus the two green bearings were totally missing. No wonder it was squealing.
Finally, the hardest part for me was re-installing the top of the dryer! Take a good look before removing it so you can see exactly how the top fits to the dryer and how the parts need to be lined up first.
Thanks to PartSelect.com! Every part was correct and the installation videos gave me so much help. Also, parts arrived in two days, which surprised me. I will be ordering all parts here.

Read less

Other Parts Used:

Drive Belt