CDWT980V00SS General Electric Dishwasher - Instructions

Simple as 1,2,3.Parts on time and priced right.

It was an install. My problem is that the drain tube is not standard to other dishwashers,so I could not get it at either of the local home improvement centers. The good news is that it is larger than the standard, and offers better discharge.

We had to replace the soap dispenser. My husband is not very handy & this was a snap. You take off the front panel (cover) of the sishwasher & simply unscrew the old one & screw in the new one. I probably could have done it myself.

I removed six screws and unplugged the module and removed.
Replaced by the new module and plugged in and then replaced the six screws.
Very easy to fix.

Very easy! Removed 4 screws that was holding the valve to the bracket. Placed bracket over water inlet line. Attached copper threaded coupling with pliers.Screwed valved on to the coupling. Attached bracket to the valve with 4 screws. Reattached water line. Attached bracket to frame of dishwaser. Put kickplate back on and done!

First, remove the bottom front covers (two parts four screws). Second, remove the two screws at the top that secure the dishwasher to the counter. Third, gently pull away the dishwasher from underneath the counter just far enough to see and be able to remove the door spring(s) - one on each side. Fourth, remove the existing hinge arm link(s) if not already broken off, replace with the new one(s). Note that the door hinge goes on the door (front) side of the spring and the other side fits into a groove on the door arm - the other end of the spring attaches to one of the 3 available holes on the frame at the bottom. It would be a good idea to replace the hinge arm links on both sides even if only one is broken. Make sure that the door has the right tension (each spring can be hooked in 1 of 3 holes to adjust the tension). Then gently push the dishwasher back under the counter. Finally, replace the screws under the counter and replace the covers on the bottom front. All of this should take no more than 15-20 minutes. This was an easy job!

hubby had no prob replacing the new part!!YEA!!dishes are clean again!

Remove top rack stops, slide out upper rack from rack railing, turn over upper rack and attach spray arm using spray arm bearing and screw. Reassemble in reverse order.

Removed screws that held dishwasher under cabinet...pulled out DW...removed old part...replaced with new....easier than falling off a stump.

Came home for lunch to discover the kitchen rug soaked and the dishes I had started when I left that morning unclean. Not sure what happened, pushed start again and immediately found water flowing out from under the machine. pulled the machine out and discovered that mice had chewed through the pliable vinyl sump tank. found the part number in my owners manual and google turned it up on Part Select. this was on Saturday and I had the part Tuesday. very satisfied

Water was leaking from under refer next to installed under counter dishwasher. Once determined to be dishwasher not refer I removed dishwasher toe place was able to see dripping inlet solenoid valve. I had to disconnect 11V power, shut off inlet water, disconnect inlet water house and remove dishwasher from under counter. Once dishwasher was in center of kitchen I flipped it upside down and removed the electric solenoid inlet valve. Removing the valve took one wrench to remove inlet hose then two wrenches to remove 90 degree brass fitting and another to hold solenoid. I used a nut drive to remove two screws that released the solenoid from the dishwasher frame. I used teflon tape to reattached the 90 degree brass fitting and inlet hose.

Twisted new one in place of old. Disappointed that there was a melting issue at all. Need to investigate problem.

very happy with the product and fast shipping. removed kick plate from dishwasher, inlet valve was on the front left bottom slid out dishwasher removed two screws and disconnected water line,and installed new inlet valve,very simple job if your somewhat handy,make sure you use thred sealant on water line when re installing

Shut off water, disconnect drain line from disposer. Remove dishwasher from wall and remove water feed line. Unplug or disconnect power to unit. Remove upper and lower dish racks as well as lower water sprayer bar, and filters. Lay dishwasher down on backside (make sure to catch water with bowl). Disconnect pump connector with nut driver and replace. Stand dishwasher back up and reverse removal process

remove front lower cover, 2 philips screws, turn off water supply under kitchen sink to dish washer, turn off power to dish washer, remove water supply line to valve, remove power to valve, clip ons, remove two 5/16" screws holding valve on, turn valve gently to access clip holding washer supply hose, push clip up hose and hold hose while pulling valve off. re-install in reverse order, a flash light helps.