3SWTW4800YQ0 Whirlpool Washer - Instructions

I removed the softener cup, unscrewed the bolt and replaced the cam kit. Super easy just like everyone else said. Parts were here very quickly and at a great price!

Removed the liquid softener cartridge.
Removed the plastic seal inside the upper agitator using a pliers.
Removed the bolt holding the agitator in place using a 7/16 socket wrench with a 6 inch extension.
Lifted the agitator out.
Separated the upper and lower agitator into two pieces.
Replaced the cam assembly inside the upper agitator.
Reversed the whole process.

First I pulled the liquid softener dispenser from the top of the agitator. Then I pulled (also by hand) the cover that was beneath it. That revealed the bolt holding the agitator in place. I loosened this with a socket set and removed it. The old Cam-Agit, which was stripped, popped out and the new one popped in. I then reassembled everything in reverse order and was done in approximately 5 minutes. The agitator works great now and we are no longer getting clumps of powder detergent in the clothes from lack of agitation.

Pushed the new one into place. No tools, no fuss and very little swearing involved. Clogg was caused by erroneously pouring the liquid detergent into the very handy opening reserved for fabric softener. I'd love to say my wife did that, but.... no, it was me. NOW, the real story. I ordered the part via the web at 10:00 a.m. It was delivered to me at 9:30 a.m. the next morning via Fed Ex. Wow! Great job at PartSelect.

Hi I took off the old one and put on the new one quick and easy

Watch video on the site and the insulation will be easy and take about 30 min.

Followed detailed instructions which were supplied with the parts. It was easy and my machine is working great with no issues. Also I just didn’t get the main drive pulley, all new parts came for the bottom end, great service and excellent parts.

Much like the other descriptions. I found the video helpful and this was the only vendor that had diagrams, so you could see how things went back together. When I popped off the top piece, everything went flying, as someone else mentioned, so the diagram was essential.

Per your directions. Note that part has been updated from original. Looks like an improvement, adds tab to grab rod, but changes installation.

I bought the cog kit. Nice directions on how to assemble but their were no instruction on how to disassemble the agitator. I wound up replacing the whole agitator for $60 vs $6 for the parts I needed. The agitator had only one nut (which you had to take off to get at the cog assembly anyway. The agitator is the way to go. The cogs are halfway down the top part of agitator with no way the get them out without a special tool or ruining the bottom part of the agitator as the clips are part of the bottom piece. If you need special tools they should be listed. If you need to be a trained technician that should also be stated. To give you parts in the middle of an assembly with no instruction on how to put them in the assembly is plain wrong.

1. Removed the fabric softener dispenser

2. Removed Barrier Seal Cover

3. Removed bolt and seal

4. Removed and replaced CAM Agitator Assembly

5. Reversed the removal steps.

Followed the video

We also purchased from this site the agitator repair kit! The youtube videos were extremely helpful!

Watched video and followed instructions. Removed rods from top cups, laid washer on its side and pulled them out. Put new rods thru, stood washer up and hooked them in. Was pretty easy, tube heavy but I'm 52 and I did it myself.
My only problem is there's no springs anywhere attaching rods to tub and I cannot find any info on 1. IF I need them 2. What kind I need. I sent email to partselect last week inquiring and still waiting to hear.

the repair went well but I still haven't received a refund for the order was was sent incorrectly. Order #22085769 order date 2/3/23