38185 - Instructions

Using plyers Pulled old switch down and out. Put new one in and pushed new switch up into position. The switch plugs into the contacts, no wiring needed. Worked like a charm. You saved me 200 dollars GE repair bill. Thanks

Defrosted the refrigerator,power off and cut the 2 wires on thermostat and sodered the new one on and shrink tube sealed the wires,refrigerator works like new!

My fridge came with only a single snack pan, and since the glass shelves are identical I decided to order the parts needed for installing the second snack pan. The glass shelf is secured in front by a round plastic pin protruding from the side of the fridge. Once the shelf is lifted upward and free of this pin, the rear retaining ears on the metal shelf side brackets can be released from the vertical-slotted metal track at the rear of the fridge. Make certain that you have the Right and Left snack pan slides oriented correctly, and positioned on the correct side of the metal shelf brackets. You’ll need to thread two self-tapping screws into each of the snack pan slides: one near the front, and the other at the rear. These screws extend through the metal side brackets into pre-aligned holes in each pan slide. When this is completed, you can test-fit the new clear plastic pan slide (drawer) into the slides to make sure it fits correctly. All that's left to do is insert the retaining ears into the appropriate pair of slots at the rear, then lower the front of the glass shelf until it's properly positioned over the plastic support pin. Now you're ready to enjoy twice the snack pan capacity as before!

took the old stop off put the new stop on

I started at the compressor and replaced the overload and the Ptcr first and that did not make the compressor start running again, so I replaced the capasitor and it still did not start, so I bit the bulett and replaced the Main Control Board and that is what I should have checked first, when I removed the old one I found a little burnt spot on the back that I could not see from the front. The new one did not look exactly like the old one, it had two more wire terminals than the old one, but just leave them blank and everything will work just fine!

I used the socket set to remove pannel that allowed me to have access to the evaporator fan. Once the fan and it's container was visible, I removed the entire fan container using the socket set. I took the fan out of the container, removed the damage blade and the damaged fan grommets. I then replace the old blade with the new blade and put the fan and the compartment back together. I am not very handy so if I am able to do this, anybody can. Ps. I was very very pleased with the services I received from PartSelect and would encourage others to use them - must admit I was very suspicious at first.

Gently pry out switch in door jam with screwdriver and pull both connectors off and put connectors on new switch then push switch back into the hole. Looked it up on the internet and video showed how to and also had link to new part, ordered and less than a week later the fridge is bright again. I have an older freezer also and it seems that they all use the same switches. Very Very easy

removed the inside fridge electrical panel and swapped switches

easy pry out, disconnect wiring, connect on new switch and press in switch.

layed fridge face first on a chair removed cover with flat head screwdriver unplugged part replaced with new part replaced cover returned to upright and plugged in

Pulled the old gasket off, approximately 5 seconds. Put the new one in, starting from the corners, with no tools, approximately 2 minutes. Coated gasket with a thin film of petroleum jelly, approx. 1 minute.

Only took a screwdriver to take two screws out & install new slide with the two existing screws. Very easy. Took less than 5 minutes. Great website I found on Google right away, just by searching for refridgerator parts. After ordering part, only took a few days to come in.

2 screws. how easy can i get.

Replaced above parts and the noise problem was not resolved. Ordered a new motor, fan blade and another set of grommets from PartSelect. The parts were delivered the next day. Took me about 15 minutes to swap the new parts in. It's been 3 days since the repair and the noise has not returned.

Because the kit did not include fasteners, had to use wood screws and superglue.