20434 - Instructions

First, I laid the washer upon its back and removed the two clamps that held the water pump in place.
with wire pliers.
Next I removed the two inlet water hoses from the pump and sat that pump aside. I then placed the new water pump upon the shaft of the washer and secured the two water inlet hoses back on the new pump wth the clamps. I tightened them with the wire pliers slipping the clamp upon the hoses. Lastly , I snapped the two wire clamps that hold the pump in place back in their groves and immediately placed the washer up right .

Flip washer on its back, Undo/flip the clips/clamps off the water pump, remove the clamps from the hose and remove hoses from water pump, slide the pump off the direct drive, line up the shaft/drive with the new water pump and slide into position and return the clamps to secure water pump in place and reattach water hoses and clamp to the water pump. There should be two hoses going to the water pump, flip washer back upright and run a cycle to make sure the problem has been fixed

Isolated problem to front section of washer by elevating and adding water. Once I identified the pump as leaking (it was pretty obvious:>)I used a screwdriver to release the snaps that hold the pump to the drive motor. After sliding the pump off of the drive motor I used the pliers I release the clamps on the two hoses. Next I logged on to Partselest.com and ordered a replacement. The item arrived in two days. I placed the pump on the motor first then connected the hoses. It was much easier to slide the hose clamps to the proper position with the pump held secure on the motor.

I disconnected the washer from the water supply lines.turned the washer on it's back. took two hoses off the water pump.Unsnapped two spring clip's.Took the old pump off and installed the new pump.That is all there was to it.

I Removed hose clamps and 2 pump clamps. I took the old pump(had a small hole burned in it) off and replaced it with the new pump. I replaced the 2 pump clamps and the hose clamps and it was ready to go.

Removed the four screws from the control housing. Disconnect wire to machine housing. Remove the two clips connecting the machine housing to the back. Remove washing machine housing. Pump is located right in front. Disconnect hoses, remove and replace pump, reconnect hoses. Replace the machine housing. This was the hardest part if all trying to reinstall the housing.Once you get the machine housing in place correctly, put everything back together. You just saved about $125 in fifteen minutes.

My friend unplugged washer turned off water to it, tilted machine back took off old, put on new. It took him about 5 minutes. Washer is working fine now, no more water leaks!

very well the part was easy to install and the part was easy to find on the diagram furnished by parts select

I followed the you tube instructions. The hardest part was realigning the washer housing on the lower frame.

1) Disassembled the lid
2) Took the front Panel off (the old water pump was in the bottom left hand corner in plain site).
3) Used flat head screw driver to gentle pry the top and bottom water pump fasterners.
4) Used pliers to remove top hose camp. Note this is where I discovered why everyone says to put the washer on it back. Water came rushing out. Luckily no damage to the motor.
5) Used pliers to remove the bottom hose clamp.
6) Put everything back together Total time <30 minutes.

Unfortunately, the water is still not completely draining. I am now looking at the hoses for obstructions. Any other suggestions?
Thanks

I unplugged the washer, put a towel down, leaned it back and held it up with one hand while undoing the clamps with plyers. Pulled the two clamps off, pulled the pump, put the new pump on, reattached the clamps. Most of this with one hand while the other held the washer at an angle.

removed two hose clamps and two metal clips
removed old pump and replaced with new
wish all my plumbing was that easy
order Thursday night got it Monday
great job
I'll be telling everyone that needs parts about you
thanks

watched a video that showed how to repair that you had on your web site. also read some of the remarks that other people left on site, one was super easy. just laid washer on its back, unhooked both water lines from pump. unhooked both metal clips holding pump and pulled off. replaced new pump in reverse order. didn't have to go thru all the procedures of taking off the body or nothing. 15min job.

Remove four screws securing control panel from the rear and tilt control panel forward. Unplug wiring harness from door limit switch. Unsnap and remove two S-clamps securing enclosure to back panel. Tilt enclosure slightly forward and remove it from wash machine. Disconnect water hoses and clips securing water pump and remove water pump. Install in reverse order. Caution: inspect water hoses closely. I had a rotten pump intake hose and found out the hard way (water everywhere).

I watched the instructional video on how to take apart and how to take washer a part and how to install the direct drive water pump. It was very easy to do. also the delivery was very fast. I will be using the site to fix other appiances that I have that is sitting around broken. Thanks for your speedy service and customer service.