Dishwasher Circuit Boards and Touch Pads
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Dishwasher Circuit Boards and Touch Pads
Your Price
$103.92
In Stock
Dishwasher Main Control Board
CONFIGURED UI SERVICE CONTROL Part #: PS16618944
This did not help, so I ordered another control board and installed it.
CONFIGURED SERVICE MACHINE CONTROL BOARD
Part #: PS16226072.
This did not help. This control board has a small orange fuse that looks like an old fashioned transistor. it was fine, as was the fuse on the previous control board.
There were two things about the Control boards that might help someone figure out what went wrong. When I took out the original control board, there was evidence of component overheating. When I installed the new control board there was a green light that was blinking.
I had hoped to complete this repair, but we have been without a dishwasher for over a month, so I bought a new one.
(I am a competent Instrumentation and Controls technician)
It could be that there is a bigger issue here; a major component failure.
If anyone has some suggestions to try, I would like to repair the machine and sell it as a used appliance. Read more...
PartSelect Number PS16873737
Manufacturer Part Number WD21X32165
This main control board is a genuine OEM part that is designed for dishwashers. It is responsible for controlling the operation of the dishwasher. It monitors all the dishwasher cycles including wash, rinse, dry, and sanitization. It receives input from the control panel and sends commands to various components of the dishwasher, such as the motor, pump, heating element, and sensors, to control the different cycles and functions of the appliance. Signs of a faulty control board include an unresponsive control panel, error codes, interrupted wash cycles, or a burning smell, which indicates a short circuit.
Fixes these symptoms
- Will Not Start
- See more...
Installation Instructions
Glen from WARDEN, WA
Dishwasher stopped working
This didn't work out well. At the beginning of September the control panel in the door started to work erratically, the lighted buttons did not light up as expected. I ordered a replacement board and installed it.CONFIGURED UI SERVICE CONTROL Part #: PS16618944
This did not help, so I ordered another control board and installed it.
CONFIGURED SERVICE MACHINE CONTROL BOARD
Part #: PS16226072.
This did not help. This control board has a small orange fuse that looks like an old fashioned transistor. it was fine, as was the fuse on the previous control board.
There were two things about the Control boards that might help someone figure out what went wrong. When I took out the original control board, there was evidence of component overheating. When I installed the new control board there was a green light that was blinking.
I had hoped to complete this repair, but we have been without a dishwasher for over a month, so I bought a new one.
(I am a competent Instrumentation and Controls technician)
It could be that there is a bigger issue here; a major component failure.
If anyone has some suggestions to try, I would like to repair the machine and sell it as a used appliance. Read more...
Your Price
$197.78
In Stock
Dishwasher Main Electronic Control Panel
I set the indicated jumper to the required position for my application and installed it. The problem was not corrected. I read that some people had problems with defective replacement boards so I contacted PartSelect to return the first two boards and reordered the UI board.
I once again set the jumper and installed the UI board and it worked immediately.
The whole repair was extremely easy. PartSelect is very good to work with. I had no problems with returns or refunds. I will definitely use them again if I have the need for any of their products. There were slightly cheaper suppliers, but PartSelect had the parts I needed in stock and they shipped my order lightning fast. They are more than worth the few extra pennies difference. Read more...
PartSelect Number PS17137050
Manufacturer Part Number WD21X24901C
This electronic control board is for dishwashers and manages the functions of the dishwasher such as washing, draining and drying.
Fixes these symptoms
- Will Not Start
- See more...
Installation Instructions
Robert from Perrysburg, OH
No lights at control panel and no start
Downloaded the GE manual from the internet. Followed the GE repair manual trouble shooting guide. The manual contains all of the disassembly and reassembly instructions. Main board had a more than one volt higher than listed voltage output. Manual does not list an acceptable voltage range so I ordered a new main board. New board had the same output and did not fix the problem. I ordered a new UI board. The new board is a genuine GE "programable" replacement board that covers multiple models.I set the indicated jumper to the required position for my application and installed it. The problem was not corrected. I read that some people had problems with defective replacement boards so I contacted PartSelect to return the first two boards and reordered the UI board.
I once again set the jumper and installed the UI board and it worked immediately.
The whole repair was extremely easy. PartSelect is very good to work with. I had no problems with returns or refunds. I will definitely use them again if I have the need for any of their products. There were slightly cheaper suppliers, but PartSelect had the parts I needed in stock and they shipped my order lightning fast. They are more than worth the few extra pennies difference. Read more...
Your Price
$208.12
In Stock
Dishwasher Configured User Interface Control Board
https://www.youtube.com/watch?v=GN5t4VFgLCY Read more...
PartSelect Number PS17137058
Manufacturer Part Number WD21X31902C
This is the user interface control board for various dishwashers. The user interface panel is what you directly interact with on your dishwasher to start and stop it and select the specific cycle you want. If your user interface panel is not responding and you have tested your dishwasher to ensure no other part could be at fault, it will need to be replaced immediately for it to regain function. Replacing this panel will requires some disassembly of your dishwasher, and will require tools like a screwdriver, wrench, and a pair of pliers. This OEM user interface panel measures approximately 14-inches wide and is sold individually.
Fixes these symptoms
- Will Not Start
- See more...
Installation Instructions
Brian from MANSFIELD, MA
Dishwasher was randomly beeping when not in use. Then eventually the display wouldn’t light up.
I first tested for 120volts to my dishwasher to verify it was getting power from my electrical panel. Then tested pins 2 and 5 on the control board to make sure there was 14 volts going to the user interface harness. After I verified that I knew it was the user interface that was bad. I watched a video I found on YouTube and followed it. This repair was fairly easy while watching the video and making sure that you use the correct pin out that comes in the box for your model. I’m not an appliance repair person and it took me about an hour start to finish. I’m going to attach the video I https://youtu.be/TI8cUjy5YOEhttps://www.youtube.com/watch?v=GN5t4VFgLCY Read more...
Your Price
$84.64
In Stock
Dishwasher Configured Ui Board
PartSelect Number PS16762507
Manufacturer Part Number WD21X31909
Introducing the Configured UI Board by GE, specifically designed for impeccable performance and lasting durability. This crucial component ensures seamless operations of your appliance by facilitating smooth user interface functions. Crafted with meticulous attention to quality, the GE Configured UI Board sustains optimal functionality while promising uncompromising reliability for your appliance. This component part ensures that your appliance runs efficiently and withstands the test of time. Invest in GE excellence and enhance your appliance's performance with this Configured UI Board. Exceptional performance and reliability are just a click away.
Fixes these symptoms
- Will Not Start
- See more...
Installation Instructions
John from DANBURY, CT
UI Control panel would not light up and not work at all. Unplugging D/W failed to correct.
Unplug the dishwasher. Remove toe kick with 1/4 socket. Unplug, by pinching, door harness connector (White terminal connector) from PC board at bottom of dishwasher. Remove the door door using the Allen wrench, place it the hole on side of door hinge where pulley attaches. Unhook the pulley attachment at the door by using a vise grip to pull the plastic up and out. Don't break the plastic! Do the same for the other side. Remove Allen wrench. Pull door in and up at the same time. Take off 2 screws at bottom of door using 1/4 or 5/16 socket. Remove the vent cover (cap) using 2 flat head screwdrivers to loosen. Unscrew by hand. Slide toward the bottom, the inner door panel off from the outer door panel. You will see the door wire harness and some styrofoam insulation. Stand with outer door facing away from you. Remove UI by holding door handle, pressing it and pull the control head, up and away from you. It should come off from the top off the outer door panel. The UI will need to be removed from this housing. Unplug the UI harness connector. Remove 7 screw with a Phillips screwdriver or 1/4 socket. There are 2 clear plastic clips that need to be pressed in to release UI from the housing. Be careful, those clips are easy to snap. Place and snap new UI into the housing. Replace 7 screws. Reattach the connector pug to the new UI board. My personality was factory set. So, no jumper pins on my board. Snap the UI housing back onto the top of your door. Delicately, remove the styrofoam and unsnap the old harness to the soap and drying dispenser. Remove the rest of the old harness. Install the new door harness and use the plastic plugs on the harness to secure to the door. Install the styrofoam insulation. Attach the inner door panel to the outer door panel by sliding inner pan up toward the top. Replace the 2 screws at the bottom of the door. Attach vent cap by hand screwing it on. Position door at the dishwasher. Use Allen wrench or helper to hold at correct angle. Use a vise grip to grab the plastic pulley to attach it to the door hinge. Do the same on the other side. Plug in the harness connector to the PC board. Plug in the dishwasher and the UI should light up! Run a load and make sure no leaks are seen around the door. Replace toe kick.
Read more...
Your Price
$110.63
In Stock
Dishwasher Machine Control Board
PartSelect Number PS17873483
Manufacturer Part Number WD21X32938
Introducing the GE Configured Machine Control Board, a critical component for your dishwasher. This state-of-the-art electronic control board is fundamental in governing vital dishwasher operations, including washing, draining, and drying, to ensure the most optimal performance for its daily use. Crafted for safety and convenience, it ensures worry-free installation when you unplug your dishwasher ahead of time, and wear work gloves for protection. Experience the difference with this efficient piece from dependable brand, GE! Make your appliance function like new again with our GE Configured Machine Control Board.
Fixes these symptoms
- Will Not Start
- See more...
Your Price
$178.18
In Stock
Dishwasher Control Panel - Stainless
PartSelect Number PS11769758
Manufacturer Part Number W10910626
The stainless steel control panel assembly is an OEM replacement part for select Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef dishwashers. It houses the buttons, LED displays, and electronic components required to operate the dishwasher. Unplug the dishwasher and shut off the water supply before installation. Use gloves for safety. Check your model’s parts diagram for included components and verify compatibility before ordering. This part may not be in stock; contact customer service or check availability online.
Fixes these symptoms
- Will Not Start
- See more...
Your Price
$166.97
In Stock
Dishwasher User Interface
PartSelect Number PS16544414
Manufacturer Part Number 5304528982
This genuine Frigidaire product is a User Interface Assembly with Board, OEM part, suitable for specific models of Electrolux, White Westinghouse, and Tappan, among others. The User Interface Assembly showcases the dishwasher settings and aids in selecting the appropriate cycle. It is recommended that the power is disconnected before the part is installed to ensure safety. Gloves should be worn during the installation process to protect your hands. This genuine Frigidaire part is an excellent choice for maintaining the operational quality of your appliance. Please confirm compatibility with your appliance model prior to purchasing.
Fixes these symptoms
- Will Not Start
- See more...
Your Price
$88.67
In Stock
Dishwasher Configured Ui Board
PartSelect Number PS16762502
Manufacturer Part Number WD21X31904
This GE Configured UI Board is a crucial piece for maintaining the function of your dishwasher. It serves as the user interface, showcasing dishwasher settings while enabling you to choose your desired cycle quickly and easily. Though this component is robust and built to last, it is recommended to wear work gloves while installing it for safety. However, before beginning the installation process, it's vital to disconnect the appliance from the power source. Choose this product for a seamless, efficient operation of your dishwasher.
Fixes these symptoms
- Will Not Start
- See more...
Installation Instructions
Brian from WYOMING, PA
User interface not receiving power and unresponsive
Remove kickplate and insulation. Pull dishwasher out from the cabinet about 1 foot. Use pliers to unhook tension chords from the door hinges at the bottom of the unit. Pull door off the hinges. Lay door flat on floor with the face down and remove the hinges using a nutdriver. In the recesses where the hinges were, remove the hex screws. Hand twist to remove the vent from the interior side. Remove the back panel of the door by sliding it parallel to the front panel to unlatch it, then lift up to remove. At the top of the inside of the door, unscrew the housing where you can see the exposed button internals. Separate the housing from the door and use a flat head screw driver or a knife to pry it apart. Replace the board and put everything back together.
Read more...
Your Price
$154.62
In Stock
Dishwasher Machine Control Replacement Kit
PartSelect Number PS12741264
Manufacturer Part Number WD21X26186
The GE Dishwasher Electronic Control Board Kit is a genuine replacement part designed to restore optimal performance to your dishwasher. This main control board manages key functions, including washing, draining, and drying cycles, ensuring your appliance operates efficiently. This kit (part number WD21X26186) may include multiple components—consult your dishwasher’s parts diagram for a complete list of included items. Replacing a faulty control board can resolve issues such as inconsistent cycle operation or failure to start.
Fixes these symptoms
- Will Not Start
- See more...
Your Price
$96.78
In Stock
Dishwasher Board
PartSelect Number PS12365196
Manufacturer Part Number 5304512731
This is a genuine control board, which works with dishwashers.
Fixes these symptoms
- Will Not Start
- See more...
Installation Instructions
Travis from OAK PARK, IL
Dishwasher not going through the wash cycle
First disconnect the power. Open the dishwasher door. Unscrew all of the screws except the top two screws. Unscrew the top two screws last and slide the door off. Unscrew the housing for the control board. Disconnect the wires from the control board(take a picture or mental note where the wires are positioned for reinstalling). Unscrew the control board. Put the new board in and go in reverse order until the job is complete. Good luck.
Read more...
Dishwasher Circuit Board or Touch Pad Brands
- Amana Dishwasher Circuit Boards and Touch Pads
- Bosch Dishwasher Circuit Boards and Touch Pads
- Crosley Dishwasher Circuit Boards and Touch Pads
- Electrolux Dishwasher Circuit Boards and Touch Pads
- Estate Dishwasher Circuit Boards and Touch Pads
- Frigidaire Dishwasher Circuit Boards and Touch Pads
- General Electric Dishwasher Circuit Boards and Touch Pads
- Hotpoint Dishwasher Circuit Boards and Touch Pads
- Jenn-Air Dishwasher Circuit Boards and Touch Pads
- Kenmore Dishwasher Circuit Boards and Touch Pads
- KitchenAid Dishwasher Circuit Boards and Touch Pads
- LG Dishwasher Circuit Boards and Touch Pads
- Maytag Dishwasher Circuit Boards and Touch Pads
- Samsung Dishwasher Circuit Boards and Touch Pads
- Thermador Dishwasher Circuit Boards and Touch Pads
- Whirlpool Dishwasher Circuit Boards and Touch Pads