Admiral Washer Hardware | Replacement Parts & Accessories | PartSelect

Popular Admiral Washer Hardware

Your Price
$5.09
Agitator Bolt
PartSelect Number PS11741866
Manufacturer Part Number WP358237
This kit contains one screw with rubber gasket and threaded sealant. The screw head is 7/16".
Fixes these symptoms
Leaking
Noisy
Pumps but will not spin

See more...
Installation Instructions
Dexter from Milwaukie, OR says,

Washer made a loud banging noise at end of spin cycle, leaked water and agitator seemed loose
After entering the model number of your appliance you will be taken to a page where all of the parts are displayed by sections. On that page about in the middle there is a heading called "Find Part B...read more

Your Price
$5.27
Cover Screw
PartSelect Number PS11740701
Manufacturer Part Number WP308685
Sold individually.
Fixes these symptoms
No Symptoms for this part
Installation Instructions
Peter from WRENTHAM, MA says,

Kenmore 80 Series Washer - Agitator Stopped Working
First I screamed at the ceiling, because I have a three year old and an infant, and the washing machine was dead. Then I went to youtube. It seemed like the "agitator dogs" were the issue.

read more

Your Price
$5.88
Hose Clamp
PartSelect Number PS11743008
Manufacturer Part Number WP596669
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This clamp is used to securely attach a hose to another part of your appliance, which helps prevent leaks from those connections. Depending on the appliance, it can attach hoses to drain pumps, water inlet valves, pressure switches, and injector nozzles. We recommend you refer to model-specific diagrams for appropriate uses and exact placement. This hose clamp is made of metal, and is sold individually. To access and replace this part you will need a nut driver, pliers, and screwdrivers. Before you begin any repair work, make sure you have unplugged your appliance, and shut off the water supply if applicable.
Fixes these symptoms
Leaking
Will not stop filling with water


Installation Instructions
jeff from lindenhurst, IL says,

Washing Machine was leaking water
Loosened the hose clamp, removed the injector valve and injector nozzle assembly, replaced both and tightened with new hose clamp. Fixed the problem for less than $20!! Washing machine is 20 years o...read more

Your Price
$6.80
Suspension Spring Retainer
PartSelect Number PS11749057
Manufacturer Part Number WPW10145155
This is a replacement suspension spring retainer for your washer. The retainer holds the suspension spring in place while the washer is operating. If you notice movement, or an unusual noise or shaking of your washer when it is in use, it could mean that the suspension spring has been disconnected because of a broken or missing spring retainer. You will find the suspension spring retainer at the bottom of the tub assembly. To replace the retainer, use a pair of pliers to disconnect the suspension spring from the chassis mount to relieve the tension. Then, remove the spring from the retaining clip, and remove the retaining clip from the bottom of the washer. Attach the new retaining clip to the bottom of the washer, reattach the spring, and stretch it slightly so it can connect to the chassis. This part is sold individually.
Fixes these symptoms
Noisy
Shakes and moves


Installation Instructions
RUSSELL from SOUTHOLD, NY says,

machine was out of balance
Removed the washing machine from the wall and found a broken spring on the floor. Began disassembling the unit before accessing your sight. (Later I viewed your video of the more simple dis assembly)....read more

Your Price
$180.24
Gearcase
PartSelect Number PS341974
Manufacturer Part Number 3360629
This is used in your direct drive washer that has a neutral drain.
Fixes these symptoms
Noisy
Pumps but will not spin
Will not agitate

See more...
Installation Instructions
Troy from Storm Lake, IA says,

Tub wouldn't turn, but motor would allow it to drain.
I took the two screws for the control panel out and tilted it up and back. Then remove the two metal clips which held the outer panel to the back panel. After disconnecting the power and water I tippe...read more

Your Price
$7.30
Retainer
PartSelect Number PS11754273
Manufacturer Part Number WPW10402178
Fixes these symptoms
No Symptoms for this part
Your Price
$5.15
Lid Hinge Mounting Screw
PartSelect Number PS11748588
Manufacturer Part Number WPW10119828
Sold individually. NOTE: The color on the screw may not be the same as the image, but will still function the same.
Fixes these symptoms
No Symptoms for this part
Installation Instructions
Michael from Claremont, CA says,

Top part of agitator (auger) was not turning
Using kit 285587 was straight forward. Removed fabric softener dispenser & sealing cap. It took more time to find the socket set (needed a 7/16 socket) with a long driver (10 inch) than to unscrew & r...read more

Your Price
$5.11
Screw, 8-16 x 1.000
PartSelect Number PS11746167
Manufacturer Part Number WP8533953
Sold individually.
Fixes these symptoms
No Symptoms for this part
Your Price
$5.23
Agitator Bolt
PartSelect Number PS11748116
Manufacturer Part Number WPW10076270
Fixes these symptoms
No Symptoms for this part
Your Price
$5.93
Hose Clamp
PartSelect Number PS11740613
Manufacturer Part Number WP285655
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installation, you will need a flat head screw driver to replace the clamp and a drill to access the screws to remove the front of the washer. Be careful if you do not have specific clamp pliers as the clamp could fly off. Once the front of the washer has been removed, take a quick look for water damage or any obvious signs of where the leak is coming from. If it is not obvious, run water to test.
Fixes these symptoms
Leaking


Installation Instructions
Stephen from Laveen, AZ says,

Drive Pump Leaked
It took some trial and error but overall not a difficult project. 1. Take the front covers off. 2. Undo the pully spring to loosen belt 3. Remove belt off idler pulley wheel and free up belt f...read more