My Orders
Admiral Washer Valves
GET YOUR OFFICIAL Admiral PARTS TO ENSURE VICTORY
Popular Admiral Washer Valves
The water inlet valve on your washing machine is used to fill the tub with cold, warm, or hot water for the wash and rinse cycles. This part could have either a blue or green-colored valve body. There are two ports for water to enter and this valve is compatible with a half-inch ID hose. It has two 3/4-11x1/2 NHT hose threads. You may have a faulty valve if your washer is leaking, has no hot or cold water, will not stop filling with water, will not fill with water, fills and drains at the same time, or is noisy. To confirm that the valve is faulty, unplug the washer when the symptom occurs. If the washer continues to fill, then the inlet valve is defective.
The water inlet valve on your washing machine is used to fill the tub with cold, warm, or hot water for the wash and rinse cycles. This part could have either a blue or green-colored valve body. There are two ports for water to enter and this valve is compatible with a half-inch ID hose. It has two 3/4-11x1/2 NHT hose threads. You may have a faulty valve if your washer is leaking, has no hot or cold water, will not stop filling with water, will not fill with water, fills and drains at the same time, or is noisy. To confirm that the valve is faulty, unplug the washer when the symptom occurs. If the washer continues to fill, then the inlet valve is defective.
Installation Instructions
Don from Wyoming, MN
Washer stopped at rinse cycle
Removed the top and back panels. Replaced
compoments and reassembled.
Test run machine. Ran like new!
compoments and reassembled.
Test run machine. Ran like new!
This part is used to help control and balance the water temperature flowing in to the washer tub.
This part is used to help control and balance the water temperature flowing in to the washer tub.
Installation Instructions
Barb from Blackriver Falls, WI
fill valve bad
took back off then removed valve replaced with new one works good
This is an inlet valve for various washing machines. Inlet valves are responsible for opening and closing as needed, to allow water to enter the washer during the washing cycle. This inlet valve features a hot and cold-water valve, as well as the necessary wire harness to easily plug it in. Since inlet valves are an electrically controlled solenoid valve, they can fail either due to electrical failure such a short, or after long, extended use. If your inlet valve fails, your washer will likely relay an error code, or it simply will not wash your clothes due to the lack of water, and the valves will need to be replaced. Replacing this valve will require a screwdriver and/or socket wrench, and some disassembly of your washer will be necessary. This inlet valve is an individually sold OEM part and does not come with any accessories or other parts.
This is an inlet valve for various washing machines. Inlet valves are responsible for opening and closing as needed, to allow water to enter the washer during the washing cycle. This inlet valve features a hot and cold-water valve, as well as the necessary wire harness to easily plug it in. Since inlet valves are an electrically controlled solenoid valve, they can fail either due to electrical failure such a short, or after long, extended use. If your inlet valve fails, your washer will likely relay an error code, or it simply will not wash your clothes due to the lack of water, and the valves will need to be replaced. Replacing this valve will require a screwdriver and/or socket wrench, and some disassembly of your washer will be necessary. This inlet valve is an individually sold OEM part and does not come with any accessories or other parts.
Installation Instructions
melinda from HARROGATE, TN
Water would not stop flowing.
*be sure to turn water off, unplug machine, and unscrew the water hoses from the rear of the washer.
1. Removed screws from the back of the washer, just the top part where the controls are.
2. Removed the panel.
3. Use a putty knife or screw driver to pop off the top panel.
4. Remove the screws from the inlet valve.< ... Read more br />5. Unplug the wires connecting the inlet valve to the washer.
6. Lift out the old inlet valve.
7. Replace with the new inlet valve.
8. Plug the new wires into the washer.
9. Replace the screws in the inlet valve.
10. Replace the top.
11. Replace the rear panel and screws.
12. Reconnect the water hoses, careful not to mix the hot and cold.
13. Plug the machine back in and you're finished!
1. Removed screws from the back of the washer, just the top part where the controls are.
2. Removed the panel.
3. Use a putty knife or screw driver to pop off the top panel.
4. Remove the screws from the inlet valve.< ... Read more br />5. Unplug the wires connecting the inlet valve to the washer.
6. Lift out the old inlet valve.
7. Replace with the new inlet valve.
8. Plug the new wires into the washer.
9. Replace the screws in the inlet valve.
10. Replace the top.
11. Replace the rear panel and screws.
12. Reconnect the water hoses, careful not to mix the hot and cold.
13. Plug the machine back in and you're finished!
Read less
This water inlet valve is a key component in top-load washing machines, responsible for regulating the flow of hot and cold water into the appliance. It electronically opens and closes to deliver the correct amount of water, balances temperature for each cycle, and helps maintain proper water levels. Constructed from durable, high-quality materials, the valve is designed to withstand frequent use and prevent issues such as overfilling, insufficient water flow, or leaks. Replacing a faulty valve can resolve symptoms like the washer not filling, continuous water flow, uneven temperature control, or water leakage from the rear of the unit, restoring efficient and safe operation.
This water inlet valve is a key component in top-load washing machines, responsible for regulating the flow of hot and cold water into the appliance. It electronically opens and closes to deliver the correct amount of water, balances temperature for each cycle, and helps maintain proper water levels. Constructed from durable, high-quality materials, the valve is designed to withstand frequent use and prevent issues such as overfilling, insufficient water flow, or leaks. Replacing a faulty valve can resolve symptoms like the washer not filling, continuous water flow, uneven temperature control, or water leakage from the rear of the unit, restoring efficient and safe operation.
Installation Instructions
Armand from WESTPORT, MA
Water inlet nozzle was stripped and leak
Remove the front panel and back panel unplug the part unscrewed the part and replace it with the new one
This is a water inlet valve for models of Whirlpool washing machines. The water inlet valve is designed to regulate and control the water entering the appliance depending on the cycle, using an electrical device called a solenoid. This water inlet valve features two inlets, one for hot water and one for cold, as well as a wire harness to power and control the electric solenoid of each. If your washer is having issues with filling, the inlet valve is likely bad or potentially worn out and in need of replacement. Replacing this valve will require a screwdriver, wrench, and pliers. This water inlet valve is an OEM part from Whirlpool and is sold individually.
This is a water inlet valve for models of Whirlpool washing machines. The water inlet valve is designed to regulate and control the water entering the appliance depending on the cycle, using an electrical device called a solenoid. This water inlet valve features two inlets, one for hot water and one for cold, as well as a wire harness to power and control the electric solenoid of each. If your washer is having issues with filling, the inlet valve is likely bad or potentially worn out and in need of replacement. Replacing this valve will require a screwdriver, wrench, and pliers. This water inlet valve is an OEM part from Whirlpool and is sold individually.
Installation Instructions
John from SAINT JOSEPH, MI
Leaking water inlet valve assembly
Remove upper rear panel with drill driver and 1/4" nut driver bit. using the angle bit holder and torx bit remove the two screws holding the assembly in place. Slide out the old assembly and disconnect the wiring harness at the machine. Slide new assembly in place. While holding it down start both screws by hand, then use the driver/an
... Read more
gle holder to tighten screws. Reattach the wiring harness and rear plate(s).
Read less
MAKE THIS REPAIR A GUARANTEED WIN
OVER 2 MILLION PARTS TO ENSURE VICTORY
$56.33
In Stock
This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.
This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.
Installation Instructions
Pat from Hilliard, FL
Post drip from water inlet
To replace the inlet solenoid valve/thermistor assembly:
Unplug the washer.
Turn the water off and unscrew the hoses from the inlet.
Unsnap the end caps from the top control panel.
Remove the exposed screws from each end of the panel (#2 Phillips).
Pull the panel out of the way and pop out the two retain ... Read more ing clips that hold the back of the machine to the cabinet. They are located under the control panel.
Remove the mounting screw from the valve assembly (1/4-inch driver).
Pull the back away from the cabinet far enough to remove the valve, but don't let the wires get cut.
Disconnect the wires. To unplug the solenoid connectors, lift the long tab with a screwdriver.
Disconnect the water outlet hose.
Connect the wires and hose to the new valve assembly. The red connector goes to the hot water valve. The thermistor wires (the two individual connectors) can be connected to either terminal. It does not matter if they are reversed.
Put the valve back in place and install the screw.
Hook up and turn the water on.
Plug in the machine and test the valve.
Unplug the power and reinstall the back and the control panel. The back-to-cabinet clips can be snapped back in place easily.
Unplug the washer.
Turn the water off and unscrew the hoses from the inlet.
Unsnap the end caps from the top control panel.
Remove the exposed screws from each end of the panel (#2 Phillips).
Pull the panel out of the way and pop out the two retain ... Read more ing clips that hold the back of the machine to the cabinet. They are located under the control panel.
Remove the mounting screw from the valve assembly (1/4-inch driver).
Pull the back away from the cabinet far enough to remove the valve, but don't let the wires get cut.
Disconnect the wires. To unplug the solenoid connectors, lift the long tab with a screwdriver.
Disconnect the water outlet hose.
Connect the wires and hose to the new valve assembly. The red connector goes to the hot water valve. The thermistor wires (the two individual connectors) can be connected to either terminal. It does not matter if they are reversed.
Put the valve back in place and install the screw.
Hook up and turn the water on.
Plug in the machine and test the valve.
Unplug the power and reinstall the back and the control panel. The back-to-cabinet clips can be snapped back in place easily.
Read less
This water inlet valve is a genuine OEM component designed to regulate the flow of hot and cold water into the washing machine. It replaces older part numbers and is engineered for reliable performance and long-term durability. The valve ensures proper water delivery during wash cycles, contributing to efficient operation and consistent cleaning results. Installation typically involves disconnecting the water supply and electrical connections, removing the old valve, and securing the new one in place. Before ordering, confirm compatibility with your specific appliance model to ensure a proper fit.
This water inlet valve is a genuine OEM component designed to regulate the flow of hot and cold water into the washing machine. It replaces older part numbers and is engineered for reliable performance and long-term durability. The valve ensures proper water delivery during wash cycles, contributing to efficient operation and consistent cleaning results. Installation typically involves disconnecting the water supply and electrical connections, removing the old valve, and securing the new one in place. Before ordering, confirm compatibility with your specific appliance model to ensure a proper fit.
This water valve is for 60% hot water and 40% cold - This is done to save on energy.
This water valve is for 60% hot water and 40% cold - This is done to save on energy.
Installation Instructions
Peter from Manorville, NY
Water would overflow from the top of the machine
The repair was very easy. Remove a few screws, switch wiring one at a time so I put them in the correct position and replace. The hose replacement was easy at the swicth but a little more difficult at the lower end of the tub due to limited space. Overall an easy job and now it works fine!
