Washer Dryer Combo Ducts and Vents
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Washer Dryer Combo Ducts and Vents
Your Price
$10.70
In Stock
Washer Dryer Combo Damper
PartSelect Number PS3535020
Manufacturer Part Number MCQ41502701
This is a pump bracket damper for models of LG washing machines. This damper is used to protect the pump within the washer from excessive vibration damage during the washing cycle. If your washing machine is vibrating or making an excessive amount of noise during the cycle, these dampers could be worn out and in need of replacement. This damper is made of rubber and measures approximately 1 inch long and 1 inch wide. Replacing this damper will require you to access the underside of the washer, or wherever the pump location is for your model. This OEM damper is sold individually, and most washers use 2-3 of these dampers for the pump bracket, so consider how many you need before ordering.
Your Price
$9.62
In Stock
Washer Dryer Combo Single Drum Glide Felt Pad
Followed other people's excellent instructions. Clean out all the dust bunnies. Schematics were a great resource. Those and the prices made me a repeat customer.
The shaft of the Idler Lever wheel was the cause, but decided, since I had it apart, to spend a little more money and replace both Drum Support Rollers and the Roller Bracket and Shaft Assembly. They showed some wear, and the parts were very inexpensive. Make sure you have snap ring pliers with prongs that are smaller than the standard 0.40 to save some aggravation with the Drum Rollers. $5 tool. Total parts were less than $60. Probably saved $150+ in labor. Quieter than ever now. Thanks! Read more...
PartSelect Number PS11742773
Manufacturer Part Number WP500121
This dryer drum glide pad is an inch long. It is made of a felt material and is used for gas and electric clothes dryers. The dryer drum glide provides a soft surface for the front of the drum glide and allows the drum to move effortlessly. If you notice that your dryer is making loud squeaking noises, it might be due to the drum glide pad being worn down or torn apart. Make sure to unplug your dryer before performing this repair. To access this part, you will need to open up the top of the dryer. The front panel and the bulk head will also need to come off.
Fixes these symptoms
- Marks left on clothes
- Noisy
- See more...
Installation Instructions
Steven from Holderness, NH
Squeeling and grinding noise
Wasn't the belt!! Changed it anyway. Should have come here earlier. That mistake added several days to the repair waiting for a second batch of the right parts. Became a pro at taking the dryer apart and reassembling, though! Easy job, just take your time and mark your wires, if you need to.Followed other people's excellent instructions. Clean out all the dust bunnies. Schematics were a great resource. Those and the prices made me a repeat customer.
The shaft of the Idler Lever wheel was the cause, but decided, since I had it apart, to spend a little more money and replace both Drum Support Rollers and the Roller Bracket and Shaft Assembly. They showed some wear, and the parts were very inexpensive. Make sure you have snap ring pliers with prongs that are smaller than the standard 0.40 to save some aggravation with the Drum Rollers. $5 tool. Total parts were less than $60. Probably saved $150+ in labor. Quieter than ever now. Thanks! Read more...
Your Price
$36.85
In Stock
Washer Dryer Combo Cover Filter
PartSelect Number PS3634953
Manufacturer Part Number 3550EL2004B
This is a lint filter guide cover for models of LG dryers. This guide cover is installed over the lint filter housing within your dryer and ensures that the lint filter is secured during the drying cycle and can be removed afterward. This cover guide measures approximately 15 inches long and 3.75 inches wide and is made of durable plastic that features two securing holes on either side of it that fasten it within your dryer. To replace this OEM guide cover, you will need a Philips-head screwdriver to remove and install it. This guide cover is sold individually and does not include the necessary securing screws.
Installation Instructions
JOSEPH from MANHASSET, NY
Broken link vet flap
Removed the old vent trap 3 screws total and replaced the new very quick and easy.
Read more...
Your Price
$15.00
In Stock
Washer Dryer Combo Damper
PartSelect Number PS8752496
Manufacturer Part Number MCQ62786001
This is a rubber bumper made for LG dryers. This bumper is installed on the inside of the dryer door to ensure the metal door does not bend or get damaged when you close it, and ensures a barrier is between the two pieces of metal when the dryer is spinning quickly. To replace this bumper, you will need a Philips-head screwdriver or drill bit. This bumper is a genuine OEM part and is sold individually, so if your dryer door requires multiple bumpers, consider that before ordering.
Your Price
$80.82
In Stock
Washer Dryer Combo Side Venting Kit
PartSelect Number PS3575086
Manufacturer Part Number 3911EZ9131X
This dryer side vent kit lets you vent the exhaust to the side or bottom of your dryer instead of the default rear position. Included in the kit are 2 straight aluminum foil outlet ducts, each 4 inches wide, along with 1 duct elbow, 1 cover plate, 1 screw, and an instruction sheet. This is helpful for flexible installation in areas where rear venting is not possible or practical. All parts are genuine replacements from their original manufacturer.
Installation Instructions
ROBERT from DAWSONVILLE, GA
Install aftermarket side vent kit
I did as I was told (by my wife). Bought the machine from Home Depot - no side vent kit - had them complete the installation today when the kit came.
Read more...
Your Price
$72.00
In Stock
Washer Dryer Combo Side And Bottom Vent Kit
PartSelect Number PS3633049
Manufacturer Part Number W10470674
This kit is used for the bottom and side exhaust. The kit includes both the straight and elbow vent.
Installation Instructions
Mark from San Diego, CA
Needed to change rear exhaust to the side to fit dryer into my closet.
First, I opened up the front of the dryer and then unscrewed the entire back piece. I assembled the new exhaust piece from the kit. Next, I took out the old straight rear exhaust and then replaced it with the elbow shaped left eshaust from the kit. Lastly, reattache the back and front pieces of the dryer.
Read more...
Your Price
$153.83
In Stock
Washer Dryer Combo Duct-air
The bottom line is that the back removes easily. You should:
1. unplug and remove the exhaust shoot
2. remove the top per YouTube or other source
3. take off the back panel over the electrical connections and unscrew the ground; tuck it inside. Don't undo any electrical connections except the ground
4. take off the screws holding the back on (8-9, one is hidden above the exhaust vent) and pull it out of the way; you then have compete access to the "DUCT-AIR" part
4. undo the clip that holds the vent tube (from the heating element) to the part
5. remove the screws that hold the part to the inside back (3?) and push it out of the way
6. remove the clips and remove the old part
7. reassemble in reverse order
I'm over 70 so I took lots of time and breaks but was still done in under two hours. The 2 clips holding the heater element tube to the part were badly rusted and should have been replaced but I made do with the old ones. Read more...
PartSelect Number PS11741422
Manufacturer Part Number WP3387911
Introducing the DUCT-AIR from the trusted brand Whirlpool. This is a genuine OEM piece that is designed to work compatibly with selected models of Whirlpool appliances. Key to your appliance's functionality, this DUCT-AIR facilitates the flow of warm air from the heater to the back of the dryer and into the drum, assuring efficient operation. Remember to unplug the dryer while installing this part and wear work gloves to ensure hand safety. This mastery engineered part is sure to be the exact fit you need, just be sure to verify its compatibility with your model before ordering. Choose Whirlpool for trusted, high-quality parts.
Fixes these symptoms
- Marks left on clothes
- See more...
Installation Instructions
Thomas from Edgartown, MA
Screen on the hot air vent disintegrated
It is odd that this part needed replacement but I am in an area near the Atlantic ocean in a vacation house which is vacant most of the year. The exhaust vent probably brings excessive moisture down to the dryer in the basement. The screen you can see at the inside back of the tumbler (where the heated air enters) rotten out, pieces fell inside and there was danger of something falling in and catching fire. I found no useful source for information (including YouTube) as this part is most easily replaced from the rear of the dryer and the available info was about repairing the heating element, the circuit board, or the exhaust venting pieces which is done from the front.The bottom line is that the back removes easily. You should:
1. unplug and remove the exhaust shoot
2. remove the top per YouTube or other source
3. take off the back panel over the electrical connections and unscrew the ground; tuck it inside. Don't undo any electrical connections except the ground
4. take off the screws holding the back on (8-9, one is hidden above the exhaust vent) and pull it out of the way; you then have compete access to the "DUCT-AIR" part
4. undo the clip that holds the vent tube (from the heating element) to the part
5. remove the screws that hold the part to the inside back (3?) and push it out of the way
6. remove the clips and remove the old part
7. reassemble in reverse order
I'm over 70 so I took lots of time and breaks but was still done in under two hours. The 2 clips holding the heater element tube to the part were badly rusted and should have been replaced but I made do with the old ones. Read more...
Your Price
$107.37
Special Order
Washer Dryer Combo Heat Duct Assembly
PartSelect Number PS3526481
Manufacturer Part Number 5209EL1001E
Fixes these symptoms
- Marks left on clothes
- See more...
Your Price
$12.85
Special Order
Washer Dryer Combo Air Plenum Bushings
PartSelect Number PS12743303
Manufacturer Part Number WE01X29929
No Longer Available
Washer Dryer Combo Blower Housing - Rear
PartSelect Number PS8689122
Manufacturer Part Number 137551800
This rear blower housing encloses and supports the blower components while directing airflow efficiently. Its sturdy construction helps maintain proper air movement and protects internal parts during operation.