Part Location Diagram of 131268300 Frigidaire Single Shock Mounting Pin
See part 31 in the diagram
( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Open until 12am EST

customerservice@partselect.com

Single Shock Mounting Pin 131268300

Rated by 2 customers 

A Bit Difficult 

30 - 60 mins 

Ratings submitted by customers like you who bought this part.

$ 23.47
  On Order
PartSelect Number PS417323
Manufacturer Part Number 131268300
Manufactured by Frigidaire
Troubleshooting
This part works with the following products:
Washer, Washer Dryer Combo.
This part works with the following products:
Frigidaire, Kenmore, Electrolux, Crosley.
Part# 131268300 replaces these:
AP2106443, 406898, 7131268300
Back to Top
Customer Repair Stories
 Average Repair Rating: 2.6 / 5.0, 2 reviews. What's this?
Sort by:
  • 1
Sorry, we couldn't find any existing installation instruction that matched.
originall shock was broken
disconnected the power and water supply.

removed the back panel.

unscrewed the contol board that blocked access to the bottom of the shock absorber.

pulled the original pins out with pliers while pressing in the piece that prevents it from working its way out.

removed the shock absorber.
Other Parts Used:
Shock Absorber Kit Single Shock Mounting Pin
  • Richard from Quincy, MA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
48 of 60 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
washing tub had broken away fm 3 of 4 supports
disconnected fm water supply and electrical ckt
move washer fm beneath dryer (stacking config.)
removed back, found 2 broken shocks (round type) and 1 broken spring (left looking from back). checked online for parts and found your site. ordered and waited a few days.

back on task, removed controls (lower left corner) to reach pins, removed front lower panel, removed pins and broken remains of both shocks. removed broken spring. left remaining spring to keep tub suspended.

back on task when parts arrived. installed shocks --note that it was not clear that there are 2 shocks in each package (so i order 2 pkgs and now have 2 extra shocks --for next time it breaks away ;-)

crafted a 'hanger' with 10ga wire and 2x4 to permit tub to be supported and/or suspended without unduly stressing new components. attached both shocks being careful to follow instructions about alternating direction and orientation in relation to plastic bushing on the shock mounting points. removed remaining spring and used short length of 10ga wire to pull spring into position and lock.

re-assembled back and front cover... re-attached control circuit. moved closer to water and electrical supply and tested through 2 cycles --no problems found.

put back into position and leveled and locked.

works fine now.
Other Parts Used:
Shock Absorber Kit Single Spring with Insulators Single Shock Mounting Pin
  • marcia from Holden, MA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers, Socket set
33 of 37 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
Questions and Answers

Ask our experts a question about this part and we'll get back to you as soon as possible!

2 questions answered by our experts.
Sort by:
  • 1
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Sterling
December 14, 2019
We are in search of the pins to assist reinserting the spring around the bellow. Do you know where those can be found or have a suggestion for an alternative? Thanks in advance!
PartSelect logo
Hi Sterling, We would be happy to do some research to find you the correct parts. However, we need your model number and the brand name to locate any information on this. Model numbers can be short or long, and could have a mixture of numbers and letters. Thank you for your question and good luck with your repair!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Denise
October 14, 2019
My washer shakes only during the spin cycle. Would this be the part i need?
For model number fafs4272wl0
PartSelect logo
Hello Denise, thank you for your question. We would recommend replacing the shock absorbers which are PartSelect Number: PS8689635 and the pins, which are Part #: PS417323 if they are broken. I hope this helps!

Was this helpful?
Thank you for voting!
  • 1
You May Also Need ?
Model Cross Reference
This part works with the following models:
PartSelect Number: PS417323
Manufacturer Part Number: 131268300
Brand
Model Number
Description
Frigidaire
38712
Washer - WASHER
Frigidaire
38802
Washer - WASHER
Kenmore
41724182300
Washer
Kenmore
41724182301
Washer
Kenmore
41727182700
Washer
Kenmore
41727182701
Washer
Kenmore
41727182702
Washer
Kenmore
41727182703
Washer
Kenmore
41727182704
Washer
Kenmore
41729022890
Washer
Kenmore
41729042990
Washer
Kenmore
41729042991
Washer
Kenmore
41729042992
Washer
Kenmore
41729052990
Washer
Kenmore
41729052991
Washer
Frigidaire
41739012890
Washer - Stackable
Frigidaire
41739012891
Washer
Frigidaire
41739022890
Washer
Frigidaire
41739022891
Washer
Kenmore
41740032990
Washer
Kenmore
41740042990
Washer
Kenmore
41740052990
Washer
Kenmore
41740142000
Washer
Kenmore
41740412700
Washer
Kenmore
41740412701
Washer
Kenmore
41740412702
Washer
Kenmore
41740412703
Washer
Kenmore
41741042000
Washer
Kenmore
41741052000
Washer
Kenmore
41741100000
Washer
Customer Service Representative

Get in touch, we're here to help!

Open until 1am EST

Contact Customer Service