Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
This surface element kit includes an 8 inch element, two wire, 2350 watt surface element, and a terminal block with all three-wire units. These high rise elements do not come with an attached trim ring.
How Buying OEM Parts Can Save You Time and Money
Why buy the real thing?
OEM stands for Original Equipment Manufacturer. Simply put, this means that the company who made your appliance is also supplying the replacement part for it.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Timothy G - December 19, 2018
Verified Purchase
Just what the handyman ordered
The braces under the old element just fell apart after a long, long time! It was a small miracle to find a replacement element on such an old model, and the installation was a tad tricky, but the video and instructions were spot on. Old one out and new one in in under 15 minutes.
★★★★★
★★★★★
Wesley T - December 4, 2018
Verified Purchase
Worked great!
At first appearance it looked as though the new part did not exactly match the original part in terms of the mounting bracket, however upon installation everything fit just right. Heats up great, looks good too.
★★★★★
★★★★★
Ronnie R - January 1, 2019
Verified Purchase
the right part
part was as expected and worked well
★★★★★
★★★★★
Phillip B - September 7, 2018
Verified Purchase
The hinge was a little different from the old one, but it work out OK.
Everything work out just find !
★★★★★
★★★★★
David B - January 22, 2019
Verified Purchase
screws didn't fit
The screws provided didn't match the element. I had to find ones that did. Element works well once I solved that problem.
★★★★★
★★★★★
Gayle K - September 15, 2018
Verified Purchase
Does not fit
WE must return this part it does not fit
September 17, 2018
Hello,
Thank you for leaving a review on the part ordered. I have sent you an email in regards to the order. Hope to hear from you!
< Prev
1
Next >
Installation Instructions
Average Repair Rating: 4.1 / 5.0, 24 reviews.
What's this?
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
tabs soldered on end of coils (2) into which wire connectors are fitted are oversize
file/grind inner corners to fit into ceramic blocks correctly
1. Turn off power to range and remove element. 2. Remove clips from ceramic guards. 3. Disconnect wiring. 4. Connect wires to new element. 5. Install ceramic guards and clips 6. Attached element to range. 7. Restore power.
Art from SEATTLE, WA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Element had burned out.
The repair was straight forward; Loosen the screw at the tilt mechanism allowing the burner element to come off the stove and then unscrew two electrical connectors freeing the burned element. The installation could have been as easy as reversing the procedure however the lugs on the new element were poorly placed making it difficult to a
... Read morettach the two halves of the supplied insulator with the clips that secure the two halves. The insulator required the wires to be bent 90 degrees which further complicated the installation. A dremel and some dielectric grease completed the task to my satisfaction. It should have been a 15 minute job. The new element functions far better that the burned element prior to its demise. I should have changed it long ago. I bought the 8" element as a back-up because this stove has only one large burner. However, given my experience with the improvement of the 6", I'll change it shortly. And knowing I may run into the same installation hiccup, I'll prefit the ceramic insulator.
Took coil mounting assembly off first, then removed or took apart one piece at a time until heater coil was removed. Then installed (with furnished screws)the new coil, following entire process in reverse. 10-15 minutes time.
All burners on stove needed to be replaced due to age
Followed instruction that came in the new parts. Each element took about 10 minutes to remove, inspect the wires, clean the connections and reconnect the new elements. The element covers that came with the kit were easy to install, and everything fit just fine. Most important thing is to turn of the electrical power to the unit BEFORE
... Read moreyou start.
followed instruction that came with the parts. Looks great and was easy to install.
William from Yukon, OK
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
0 of 1 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Two 6" and two 8" burner elements needed replacing on a 36 year old counter range.
First of all I want to thank PartSelect. I have been looking for these parts for over 15 years. I am so happy to have found PartSelect. 1. Turn off Range 2. Turn off Breaker to the Range at your home Breaker Box. 3. Turn on Range to see if you turned off the right Breaker if so then turn Range off. 4. Lift Burner Element up. 5. Take off S
... Read moreilver Trim Ring and Drip Bowl. 6. With screw driver unscrew the screw that is holding the Burner Element to the Range. It is located at the base of the hing where the Burner Element attaches to the Range. 7. Pull the Burner Element out just far enough to see the entire Element where the wires attach. 8. Snap off the two silver clips from each side of the White Glass Insulation Block with a screw driver. 9. With an adjustable wrench (crescent) loosen and remove the screws holding one of the wires to the Burner Element. 10. Find the same Terminal on the new Burner Element and reattach the wire to the new Burner Element Terminal. 11. Now do the same to the remaining Terminal. 12. Install the White Glass Insulation Block over the two Terminals and secure with the two silver clips. 13. Reattach Burner Element to Range with screw. 14. Replace Silver Trim Ring and Drip Bowl. 15. Turn on Breaker and test by turning on Range. You will smell a slight electrical burn smell for a moment while the new Elements heat for the first time. This will dissipate quickly. NOTE: I used the old White Glass Insulation Block I did not use the one that came with the new Burner Element. I found the old one to be the better choice. I saved the new one in case needed at a later date. The Job to replace both the 6" & 8" Burner Elements took less than 30 Minutes. I think it took longer to write this replacement instruction. LOL Very easy...Thanks again PartSelect. Charles McAllen, Texas
burners on stove & oven element had begun to over heat and one had broken apart
Ordered replacement burners & oven element thru your website and installed. Burners & oven are working fine now. I have had to order an oven element in the past; about 5 - 8 years ago. I've owned this stove now for over 20 years.
One burner was not level and the otherone I burned out tea kettle on it and when I pulled the kettle off the burner it was also not level not to mention part of the kettle was burned onto the burner.
I didn't turn the power off which was risky and dangerous, however it was very easy just removing one screw a couple of wires and installing the new one. VERY EASY!
Easy to do . Four screws,removed cover,removed switch. Installed switch,and cover. Time 1/2 hr.
RONALD W from PISCATAWAY, NJ
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers, Wrench (Adjustable)
0 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
2
3
Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
2 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
David
November 19, 2019
Can this part be used on a tilt lock surface unit?
For model number JSP27J
Hello David and thanks for writing.
We believe you are referring to part # PS244050
tilt lock surface unit. please let us know if you need any further assistance. We hope this helps. Please contact us anytime
Is, your part number: Ps244046 the correct 8" coil stove top element for j bp22 r3wh stove? The plug-in tips do not look the same as mine. would i be replacing the socket as well as the element?
For model number J BP22 R3HW
Good Day Bob. Thank you for your question in regards to your unit. The model number you provided is not recognized. Please verify the number you provided us. If it is correct, we recommend contacting the manufacturer and seeing if they could provide you with a part number, and then you are always welcome to check back to see if we carry the part! Best Regards.
Did this question help you?
Thank you for voting!
< Prev
1
Next >
Model Cross Reference
This part works with the following models:
PartSelect Number: PS244046
Manufacturer Part Number: WB30X348
Item is in stock and is estimated to be delivered in 2-3 business days via Standard Shipping.
On Order
Item is not in stock and usually ships 3-5 business days from the time you place your order.
Special Order
Item is not in stock and usually ships 10-15 business days from the time you place your order.
NLA - No Longer Available
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
[{"position":0,"name":"Home","title":"Home","url":"/"},{"position":1,"name":"Range","title":"Range","url":"/Range-Parts.htm"},{"position":2,"name":"Element or Burner","title":"Element or Burner","url":"/Range-Elements-and-Burners.htm"},{"position":3,"name":"WB30X348","title":"WB30X348","url":""}]
You added 1 item to your cart
✖
% OFF
$
$
Qty:
Total item(s) in cart:
Order Subtotal
$
*Taxes and shipping will be applied during checkout
