Front Glide Kit 306508

Hi Trey, it sounds like you need to replace your front tumbler bearings 306508. Do not panic as this is normal wear and tear for your dryer to experience. Also, the heavier loads you put in your washer, the more wear the tumbler bearings will have. I hope this helps.

Hi Jason, Thank you for your inquiry. There are three parts that may fix the issue. The front and rear seal, the dryer drum glides and the drum support rollers. Front and Rear Seal A worn, torn, or missing front or rear seal could be the reason your clothes are coming out of the dryer torn. The seal is designed to keep clothes from getting between the drum and the front or rear wall of the dryer. If this seal becomes worn or torn, your clothing may become lodged between the two parts. Because the dryer drum keeps turning, the clothes get ripped. Before you can examine and replace a dryer drum's seals, you have to remove the drum. Dryer Drum Glides Torn clothing could mean that the glides in your dryer have become defective. The glides support the drum towards the front of the dryer. They can wear over time, causing the drum to slump or sag toward the front of the dryer. When this happens, a pinch point is created at the top of the drum. It is this pinch point that can tear clothing. If this happens in your dryer, you will have to open it up and replace the entire set of glides. Drum Support Rollers Another possibility for torn clothing could be defective drum support rollers. The rollers support the drum in the back of the dryer. These too can wear over time, causing the drum to slump or sag in the back. Again, a pinch point is created, causing clothing to tear. If it is the drum support rollers in your dryer that have become defective, you will have to replace the entire set of rollers. You will have to open up your dryer's cabinet and remove the drum before you can replace your drum support rollers. I hope this helps. Thank you and have a great day!

Hello Ralph, Thank you for your inquiry. Usually they do not, so we would recommend checking the drum rollers, the roller shaft/axle, the idler pulley, the drive belt, the drive motor and the felt seal. Hope this helps!

Hello Penny, based on your symptoms the most common reason this happens is worn rollers, which are found here 12001541. Before ordering this assembly, we suggest checking your rollers to see if they have excessive visible wear to the point that they look damaged. If that is the case you should replace them. Please let us know if you have any further questions.

Hi Clint, Thank you for your question. It is normal for the blue plastic piece and the drum glides to wear down through use of the dryer. I hope this helps. Thank you and have a great day!

Hi Kathleen, Thank you for your question. If one of the baffles in your dryer is broken, you will need to replace it. Sometimes while the clothes are drying, the clothes may become caught on the baffle and as the clothes are heating, the area of the clothing where it is hooked on to the baffle can become black with scorch marks. I hope this helps. Thank you and have a great day!

Hi Andre`, you are correct. Based on your symptoms it sounds like you need to order a tumbler bearing kit 306508. Best of luck with this repair.

Hello Odette, thank you for inquiring. For this symptom you will want to replace either the Drum Glides, the Drum Bearings or the Drum Support Rollers & Shaft. If you could provide the model number for the appliance, we can confirm the correct compatible parts.

Hello Fran, thank you for writing. The Front or Rear Drum Felt Seal for your model is part PS11740771. We have a video for it showing what you need to know to install it. Here is a link: https://www.partselect.com/PS11740771-Whirlpool-WP314820-Front-or-Rear-Drum-Felt-Seal.htm?SourceCode=4&SearchTerm=LDE7304ACE&ModelNum=LDE7304ACE#RepairVideo. We hope this helps.

Hi Douglas, Thank you for your question. The temperature for your refrigerator is preset at the manufacturers. If the refrigerator is locked, there should be green light lit just above the button. If the controls are locked press and hold the Lock/Unlock button for three seconds until the green light turns off. If the temperature alarm light is flashing, press and hold the Temp Alarm button for 3 seconds to turn it off. If this is not the issue, you may need to check the connections between the touchpad and the electronic control board. I hope this helps. Thank you and have a great day!