YMERH770WS1 Whirlpool Range - Instructions

very easy

Screwed in light bulb and glass protector

Took off the screws on the back of the stove and took out the sensor, and put in the new one.

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

Removed door from oven. Removed 6 screws to dismantle door. Removed 3 more screws to remove hinge from door...reverse order to assemble.
Very easy

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

This is a built-in oven, so the biggest problem was figuring out how to remove it from the cabinet. The solution turned out to be removing the cooktop above it and unscrewing two screws that connected the oven to the inside of the cabinet. The other problem was removing BOTH metal backs from the oven. The first one was easy. The second one wasn't. The old socket was recessed behind the second back, making it virtually impossible to access the metal "wings" that hold it in place, so I ended up pulling out the socket assembly from inside the oven with pliers.

Changing out the baking element was fairly easy. Shut off power at breaker. Remove the baking trays and the 2 screws at the bottom of the inside back of the oven. There are 3 screws to remove the element. Slide out the connectors and replace. Additionally, the baking element blowing resulted in a blown relay inside the control unit. Unfortunately it is an all in one unit that includes the touchpad PCU board as well. To replace it you must remove the upper rear panel off the back of the oven, remove the electrical connectors, remove the 4 screws and the unit. Put the new unit back in and go in reverse. Power up to test.

First, I received the element in two days. My local repair store said it would take them a minimum of 10 days to get the part. My husband replaced the element after watching the youtube "how to" video. He knew exactly what to do and did it in about 30 minutes. We were using the oven the next day. Thanks!

The range in my classroom had the leveling legs broke off by the summer staff. I ordered two new leveling legs and the night custodian replaced them in about 45 minutes and them leveled the stove. Parts were just as stated and easy to order.

First I took the door off and outside to dump the glass in the trash which I had some Kevlar gloves so not to get cut. Removed the three screws on the bottom trim piece and the two on the sides remove the outside face glass next remove the four screws that hold the next glass. This glass is in a frame there is bent tab on one corner unbend open frame and install inner glass close frame rebend tab and reinstall all the parts.

Easy just loosened screws took apart door, removed broken glass and installed new glass.It took longer to clean the stove! Lol!

Turn off power--Remove bottom cover inside the oven---Undo three screws holding broken element in place--Remove element by pulling out ,and carefully detach from power connection.Reverse the procedure with the new element.In doing this myself I saved $90 for a repairman to come and diagnose the problem, and another $90 to bring back and install the element which cost $62

Exactly how the video provided showed. It was pretty simple.I feel pretty cheesy about doing this myself. Thank You!

First removed 3 screws from top of door and the 3 bottom screws. To remove hinges there are 2 screws on the bottom ends remove those and then there is 1 in the center of hinge remove slide out old hinges and install new ones.The hinges have to be in the extended position I then put the needle nose pliers on the top end of hinge because they kept snapping shut before it engaged with the receptacle I put on one side when it was in I released the plier and it hooked I then proceeded to the opposite side it shouldn't have taken so long once I used the locking plier I was done in 10 minutes.