WRF550CDHZ03 Whirlpool Refrigerator - Instructions

I unpacked the glass and slipped it into the shelf. Done.
What was more impressive was the delivery time. I ordered the glass at about 12:30pm one day and the glass was at my door by 9am the next morning. Even my husband was impressed with that.

took out old lid, took out drawers above this drawer to make it easier to work on. installed new drawer simple by hand with no tools. put other drawers back. very simple no tools needed.

The broken one just popped out and the new one popped right in! This company shipped out the part I needed immediately I had it in two days!! I highly recommend them!!

Extremely simple to replace the entire cover. Just had to press on the sides to remove the cover from the hinge pins, then reinstall.

stick the very small screw driver in the hole on the left side cover and lift up to release the keeper tab,pull out to expose the wire connecter.insert the small screw driver in the slot on the left side to release the tab while pulling apart the two connectors.tuck the wires tight to side and pull out the ice maker.I thought I was getting the whole ice maker assembly,but just got a part of it,so I had take it apart and put it back together.the hardest thing to change over was the stop lever arm that senses the level of ice in the bin.after all this,it didn't work at all.not happy around here.back to filling ice trays

No product was sent in the box for the shaft I received an empty box from them cannot perform any repairs because I got no product from this company. Called customer service said due to Covid no customer service available when online and receive no customer service no refund no product no help

Replaced motor it was not issue. Now I am stuck with a $300 motor I cannot return. When I say will not dispense ice everyone thinks it does not make ice. Auger does not turn to push ice out the door. Reason I thought it was auger motor when you push lever on door the auger turns about one eight of a turn. So, it would seem it is getting signal and power. Cannot find any articles on this specific issue. If anyone has a suggestion, please share.

after pulling the draw out. had to remove 3 screws on the left side, pull out one part, and then replaced the broken pin. put everything back in place and it was done.perfect job.saved alot of money. thanks to part-select

It was very easy. I removed the two crisper drawers and the glass shelf above the pantry section. I removed two bolts with a nut driver and one screw from the slide track. I pulled out the broken piece and did that all in reverse. Took 5 mins tops.

Also I wanted to say I got my replacement part in two days with standard shipping.

Part select sent the WRONG part which I returned. They refunded the cost of the bin and tax but did not refund the shipping fee (which was paid to them for shipping me the WRONG part). i'm also out the shipping fee for sending the WRONG part back to them.
Installation was inconsequential; the service was terrible

I removed the Deli Drawersvegatable and fruit drawers. Removed the glass panel. Removed the screws holding the Endcap and snapped the old one out. A back panel strip that controls the humidity snapped out. I installed the back panel to the new endcap. Installed the new endcap snapping it in place and used the screws to keep it in place.
It was not difficult and everything fit perfectly. The only thing it takes is a little understanding as to how it all fits together. It took about 20 minutes.

We removed the old switch, unplugged it, plugged the new one in and it was easy to do. But when we tried to put the switch back in we had a very hard time doing it. Eventually got it in, but if it had not been for the difficulty we had getting the new switch to snap in to place, it would have taken under 5 minutes.

Took off old one and just replaced new, very easy and corrected problems!

Thanks to others who shared their story, I was prepared to "muscle" the front cover off the old crisper and snap it into place on the new crisper -- warning if you are good with puzzles and mechanics, this repair is a "snap"; Pantry Lid is very easy, push pin on left side, slide old lid out and push new lid in.

Removed two 1/4" screws from the end cap with the nut driver and removed it. Transferred a few pieces from the old end cap to the new. Reinstalled the new end cap and presto, job complete.