WRF550CDHZ03 Whirlpool Refrigerator - Instructions

Removed door and crisper pans.
Removed nuts on left end cap - think there were 3.
Removed nuts on right end cap and one or two on back air regulator attached to right end cap.
Replaced left end cap with new one using reserved nuts.
Carefully removed back air regulator from right end cap.
Attached back air regula ... Read more tor to new right end cap.
Replaced right end cap and back air regulator and attached with nuts.
Carefully inserted pantry door into pin on one side and slightly bent both right and left pins to insert door fully into end caps.
Replaced crisper pans.
That's it.

The video on website is very good and explains everything in detail. Just follow the directions. This is EASY!!!!

I used a flat screwdriver and released the lock tab on the bottom of the light switch, and pried the switch out, being careful to not damage the plastic around the mounting place of the switch, unplugged wiring from old switch, plugged in the new one and pushed the new switch into place. Job finished light switch now working.

We had periodic leaks from under the Unit from new, could never figure out where it was coming from. Finally as it began to cause damage to surrounding cabinets, we took the back off and found the multiple cracks in the drip pan. Someone had hand trucked it from the wrong side! It was difficult to figure out the fan removal (it sits in th ... Read more e pan) but push the top forward and pull the bottom back and the fan came out. Then the pan was simple to remove / replace, by reversing the removal procedure, the fan was re installed.

The lid that covers the front of the lower meat / produce drawer hinges upward on two small ( easily broken) plasic pins, one on each side of the drawer. One pin is moulded into each "END CAP" that also supports the drawer glides and glass shelf above. The entire end cap must be replaced to repair the hinge. The left side is easy (it's ... Read more the only one I had to replace); the right side might be more difficult because the right end cap includes a temperature control.
1) Remove the two produce drawers above the lower drawer.
2) Lift off the front glass shelf support, the glass shelf, and the rear glass shelf support from below the two produce drawers.
3) Slide the lower drawer half way out. Remove the drawer lid by disengaging it from the remaining undamaged hinge pin on the OK end cap. Careful not to break the good one.
4) Slide the lower drawer all the way out, then lift up and towards you to remove it from its glides.
5) Using a 1/4" nutdriver or socket, remove the three recessed screws. Leave the drawer glide alone for now.
6) Pull the front of the end cap up and towards you about 3/4" to disengage it from a small retainig button at the top front. Pull the end cap toward you to disengage the two rear retaining fingers.
7) Using a small Phillips screwdriver, remove the drawer glide from the broken end cap and attach it to the replacement end cap. Note which end is the front before removing it.
8) Reassemble in reverse order. Again, be careful with the hinge pins.

The frig. no longer cool downed or operated at all as the electronic control panel was dead. Pulled old part off and put in new part, following instructions on You Tube. However, this part did not solve the issue. I had to call a repairman. The repairman said that another part was needed also, this part costs over $400.00 but, the part wa ... Read more s no longer available. I had to purchase a new frig. and not a happy camper to have a 6 year old frig,that a part is no longer available.

First I looked at new replacement part, saw what held the part to the frig. Then removed the crisper drawers and vegie drawers and related support pieces. Used socket wrench to take out three screws and started so remove endcap. Realized endcap was attached to a piece that controls air flow to drawer, located supporting screw, removed ... Read more and entire assembly came right out. I fumbled my way through the linking mechanism being very careful not to force and break anything. Once I figured out how all this worked, it went back together in a few minutes. Replaced the four screws that held the 2 pieces (endcap and airflow) to frig, replace drawer slid, replaced all draws. Done 30 minutes, start to finish. I found Customer Service VERY helpful while ordering piece, couldn't believe it was under $10 and fit exactly! Thanks PartSelect.com!

Remove the light cover. Use a flat head screw driver to push in the tabs on the back of the program mount and pull down to expose the computer board. The Thermistor is clipped on under the vent holes on the right side. Cut both wires to remove the old thermistor strip a 1/4 inch off the remaning wires and the new thermistor wires twist bo ... Read more th ends together crimp on the wire caps snap in the new thermistor reinstall the program board until the retainer clips snap into place, slide the light cover back on.

Pushed the hinge pins aside and removed the old lid.. Reversed the process to install the new lid

First, I removed the drawers at the bottom of the fridge and then I removed the three hex head (7/32) screws that hold the end cap on. Then I disengaged the slider which connects to the temperature control for the pantry drawer. Then, unscrewed the drawer slides with a Phillips from the old end cap. Also the slide push rod has to be di ... Read more sengaged from the clips on the back of the endcap.

Then, I reinserted the push rod to the new end cap and reattached the drawer sliders and the slider itself. At this point I realized I SHOULD have unscrewed the temperature slider at the back where it covers the cold air outlet. The screw had slipped out. I replaced it with a slightly larger wood screw. Reinstall the drawers, all done.

I unboxed the replacement gasket set and inspected them for damage. Then I opened the left refrigerator door and grabbed the right hand corner of the old gasket and removed it. I then aligned the new gasket with the door and using my fingers pushed the gasket into the gasket grove. I used my thumb to seat the gasket. I repeated the proce ... Read more ss for the right door. Total time was under 15 minutes.

Since the crisper didn't come with a front, the old front needed to be removed from the broken cripser and attached to the new one. The easiest way to take off the front is to remove it from the bottom of the crisper. Once the pressure is released it comes off easy. Snap the front on the new crisper by starting with the top and snapping t ... Read more he bottom.

This is the 2nd part I have bought for this refrigerator from Part Select. I wish the parts came with some kind of instruction. I had to re-use parts from the original equipment each time. After studying the replacement part I was able to figure out what I needed to do, but it would have been nice to have a little more information. Th ... Read more ere were 3 pieces which I needed to remove from the damaged piece and add to the replacement part. I would gladly pay more for a complete replacement part.

Watched Partselect video of P-trap installation.Removed water line & back cover& disconnected wires to water solenoid .Removed old drain tube & old problematic rubber funnel. Used contact cleaner to clean rubber residue from drain line and used a little silicone to aide reassembly. Job went well thanks to video.

First, I removed the Climate control drawers, the lower shelf pieces and the Chef's Pantry drawer so I had room to work.

Next, I unfastened the two screws that held the pantry drawer gilder on the broken righthand end cap and removed the glider.

With a socket tool, I unfastened the three socket-head mounting screws ... Read more that held the endcap to the refrigerator wall.

The righthand endcap has a climate control adjustment mechanism which includes a finger slider and an extenson bar snapped to the backside of the endcap. This extension bar connects with another bar mounted to back inside of the refrigerator.

I carefully disconnected the climate control mechanism fixed to the refrigerator from the endcap.

With the endcap out of the refrigerator, I next had to disconnect the climate control slide and extension bar from the broken endcap by unclipping several snaps holding these pieces in place.

Now with the new endcap, I clipped the extension bar in place, snapped the finger silder in place, and reconnected this assembly to the climate control bar in the refrigerator and clipped the mechanism to the rear of the endcap.

The socket mounting screws were used to fasten the endcap to the wall. The pantry drawer glider was attached to the endcap with it's screws. The shelves and climate control drawers were put back. Finally, I carefully snapped the Pantry door to the hinge pins on both the left and the (new) right end caps and put the pantry drawer back.