All Installation Instructions for Whirlpool Range WERP3101SS2

surface element out

Unplug from outlet and top remove back section of range and unplug wiring from switch, remove knob and unscrew two screws and remove old switch. Install new switch reinstall screws and plug switch plugs into new switch (will only go on the correct way). reattach back and plug into outlet. All done and surface element works perfectly.

Parts Used:

Surface Burner Element Switch, Large Burner

Edward from TAYLORS, SC
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

element not working properly

Remove 2 screws inside oven holding element . Remove screws holding back panel. Plug wires (2) into new element.Install back panel . Done.

Parts Used:

Broil Element

PHILIP from NORTH PORT, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Burner wouldn't regulate temperature

Turned off power to range. Took back panel off to reveal all controls. Pulled off knob of bad control. Removed 2 screws from the front of the control. Pulled off wiring from back of old control. Took new control reversed procedure. Reinstalled back panel turned power on and tested new control. Total time about 20 minutes

Parts Used:

Surface Burner Element Switch, Large Burner

Michael from THE VILLAGES, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Element temperature inconsistent

Turn off power to the stove (unplug or turn off breaker)
Remove back panel screws (Phillips) and back panel
Unplug switch
Remove knob and attaching screws (Phillips)
Remove and replace switch
Reinstall screws for switch and plugs in the back
Snap off the end of the stem if it's too long and reinstall knob
Reinstall back panel and turn power back on

*important: the large element has an updated switch and you may need to snap off the end of the stem with pliers! It's too long and there are no instructions for this included!*

Parts Used:

Infinite Switch - 6 Inch

Nathan from WHITE RIV JCT, VT
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

screw came off

very expensive to buy the part but just tighten the screw intot eh predefined place.

Parts Used:

Range Screw

Sandeep from EDINA, MN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Oven Elementwas burnt into

Watched the video and did as shown

Parts Used:

Oven Bake Element

Fred from APACHE JCT, AZ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

2 Service Elements Didn't Work (Didn't heat up)

Unplugged old elements and plugged in new ones

Parts Used:

Range Surface Element

Standard Y-Frame Range Surface Burner

Roseann from MEADVILLE, PA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Old drip pans made to heating element un ever

Replaced drip pans and now everything is level.

Parts Used:

Drip Bowl - 8 Inch

William from DANBURY, CT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Removing an heating element that burnt into .

Unplugged oven , removed screws ,pulled wires out, removed old element , just hooked wires up , screws .make sure it sits level plugged in. Works great

Parts Used:

Oven Bake Element

Jenny from GREENFIELD, IN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Oven Demon Possession

Our repair was extrodinarily easy. As my husband was taking out the old element and the oven was off, the element heated up and actually burned him. He readjusted it and it refused to heat again. We figured at that point that there must be a short, so we never even opened the box with the new element. A short time later we decided to use the top of the stove for soup and a small fire started in the oven. We turned off the braker at that point and ordered a new oven.

Parts Used:

Broil Element

Kevin from Greensboro, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

baking element non operational

removed two screws to faceplate at rear of oven. Disconntected contact wires, installed bake element reconnected contact wires, attached faceplate turned on oven holy hell it works just saved some money on service call thanks!!!

Parts Used:

Oven Bake Element

GARY from JACKSON, WY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

The heating element on the left front burner was out

Pulled the old one out and plugged the new one in. It was that simple!

Parts Used:

Range Surface Element

Julie from Salt Lake City, UT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Worn/Bulb Socket

It was alittle difficult at 1st to remove the clips that held in the socket. But once out everything went smoothly.

Parts Used:

SOCKT-LITE

JOSEPH from COON RAPIDS, MN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Shorted oven contoller and display module

Tool out 4 screws, unpluged the connectors, unscrewed two screws holding the module. Replugged the connectors, replaced screws. Done (don't forget to turn the power off)

Parts Used: