All Installation Instructions for Whirlpool Range WERE3000SB2

8” burner on low would run away. Burn solid red.

I installed the new switch. No difference. I switched elements with the other 8”. Same thing. I called Part Select and their rep said he doubted the new switch was defective but if it was they would replace it. But first how about trading the new switch with the other 8” switch that is working. I did that and the new switch worked fine on that burner but the old switch that worked before allowed the bad burner to go to red hot. Now I’m at a loss. All I see is a new stove. I don’t know what to do next and am open to any and all suggestions.

Parts Used:

Surface Burner Element Switch, Large Burner

Paul from SHELBYVILLE, TN
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Element had burned out, and the drawer glides were broken .

Replaced both .

Parts Used:

Oven Bake Element

Range Rear Drawer Glide

Allen from ASHLAND, PA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

burned out stove eye, 6"

remove burned out eye, replaced with new eye.new eye does not fit exactally correct onto splash pan as point on end of steel " rod " not pointed enough to slip into mate on splash pan

Parts Used:

Standard Y-Frame Range Surface Burner

Robert from Birmingham, AL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Glass Door Broken

Removed 3 screws holding the glass door bracket.
Placed glass into door holders, had another person hold glass while I replaced the removable bracket screws.

Parts Used:

Range Exterior Door Glass (White)

Myron from Punta Gorda, FL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

3 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Oven temperature was 50 degrees off

Unplugged stove.
Pulled stove out.
Unscrewed screws and removed cover.
Removed & replaced sensor.
Reinstalled cover & screws.
Plugged in stove and pushed back in.
Only problem was when I pulled stove out, lid opened and disconnected the gas line to a burner.

Parts Used:

Oven Sensor

Gregory from BRIDGEBORO, GA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

cleaner

just needed clearner for the top of my glass top, the operator was very helpful I received my clearniner in 7 days thank you

Parts Used:

Cooktop Cleaner

Mary from Duarte, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 5 people found this instruction helpful.

Was this instruction helpful to you?

My drip bowls were scorched and discolored and difficult to clean

I removed each surface coil burner from its receptacle; removed the old drip bowls and replaced with the new ones; my stove looks good as new.

Parts Used:

Drip Bowl - 6 Inch

Drip Bowl - 8 Inch

Claudia from Milwaukee, WI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Burners needed replacing

Pulled out the old burners and put in the new ones.

Parts Used:

Standard Y-Frame Range Surface Burner

Alene from INDIANAPOLIS, IN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Light would not light

Pop old one out and new one in

Parts Used:

SOCKT-LITE

Frank from LEBANON, VA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Replace burner drip pan

Removed electric coil replaced pan and reinstalled coil. Part fit just right and no problem.

Parts Used:

Drip Bowl - 6 Inch

Drip Bowl - 8 Inch

Ray from Council Bluffrs, IA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

surface burner heating element broken

took out old element, replaced with new.

Parts Used:

Range Surface Element

Marlene from Charleston, SC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 6 people found this instruction helpful.

Was this instruction helpful to you?

reflecter/drip pans wrong size

Ordered acording to range model & such. Had ben unsucksessful gettin the right size thru the years & finally got the correct ones.

Parts Used:

Drip Bowl - 6 Inch

Drip Bowl - 8 Inch

Dann from Glendale, AZ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Eroding burner drip bowls

Removed old drip bowls and installed new, which, thanks to your efficiency, were a perfect replacement

Parts Used:

Drip Bowl - 6 Inch

Drip Bowl - 8 Inch

Edward from Hamilton, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

slides on lower drawer were broken

I used a phillips screwdriver and replaced the part with one screw.Very easy and replaced my lower drawer under my oven,it tool about three to five minutes at the most and my drawer works fine now.Thanks for the instruction video on line, it really helped.

Parts Used:

Range Rear Drawer Glide

Leona R from Louisville, KY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

burned oven bulb

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

Parts Used: