WCSR4170D2CC General Electric Washer - Instructions

IT was so easy to replace the pump. I think the hardest part was trying to get the pliers to work right. All I had to do was unscrew two bolts, take off two pipes, get the new pump and replace the pipes and bolts. It was that easy.

Use paint scraper to release spring tabs holding front cover on.

Removed 2 screws holding lid down, and lifted up but did not remove top cover and control panel.

R/R 2 hex screws holding strap in place. If you are lucky and the broken strap is up front this is a super fast repair. Those of you with a rear strap will want to disconnect the wiring harness to the lid switch and likely remove the top panel (+ <5 mins).

Super easy and super cheap!

Followed your video instructions and removed agitator.Used 7/16 3/8 in socket wrench to remove bolt in the agitator coupling and replaced coupling. Put new bolt in and tightened. Installed Agitator.Works Great.

Popped off the front panel and removed two screws that help top down. Then pulled the top of the washer up and leaned back out of way.Then each strap had a screw on each end and a clip that holds straps just remove the old and replace with new and put back together.

used a socket to unscrew the clip. pulled out the old hose, slid the new hose into the clip and screwed the clip back on. all fixes should be this easy.

Unscrewed 4 screws to remove the front cover, disconnected the old timer and plugged the new one in. So easy.

You tube is the only way to go!

Followed video to take washer apart. I used the Shaft & Drive Assembly to tap out bearing as it was stuck. BTW the screeching was because the Shaft & Drive Assembly ball bearing retainer cage was in pieces. Replaced tub bearing and installed new Shaft & Drive Assembly. Washer now runs like new. Get the spanner wrench to remove existing nut and purchase a new nut.

First, remove the old water pump by disconnecting the respective hose, then wipe the area where the pump was, and proceeded to connect the new water pump, of course I did all this with the machine disconnected from the power electric, then proceeded to connect the inlet hoses of hot water and cold water, electricity connected to the machine and did a test with clothes in the washing machine. and now everything is going well, thanks for your valuable help.
sincerely, a satisfied customer

Followed video on You tube that showed step by step how to compete repair.
The machine used in video was brand new and there was no corrosion on any parts so disassembly was much easier in video than on 9 year old machine.
Also reinstalling drive belt was a little tedious but overall job very straightforward and resulted in positive improvements in performance and greatly reduced noise levels.

I watched the video from the web site and the one that came with my invoice. This made it very easy to fix.I got the tools that I needed and went to town on the repair.

We pulled off the bottom cover to access the pump. The washer was on its back and that made it easier to reach. There was two hose clamps to pull off along with the two electrical parts. Very easy to replace.

First I located the trouble. I noticed that it was water leaking and figured it had to be a hose. I took the front panel off of the washer and after noticing that the drain hose had a slight hole in it, realized that I could fix it and save myself a repair call. I undid the two hose clamps and removed the hose. I went to a local repair shop that could not guarantee the right part. I went online and found Parts Select.com. I entered minimal information and the picture of the item that I was looking for, the Drain Inlet Hose, was staring at me! Within 3 business days and less than 20 dollars spent, I repaired my washing machine. The total time spent to repair after I received the hose took about 10 minutes. I will definitely use parts select .com and recommend to all my friends and family. Thank you.

First buy the tub nut wrench. I can't over emphasize that! $12 at amazon. With out it getting the inner tub out will be the worst part of the job. And you will have to buy a new nut. I had trouble getting the old bearing out of the outer tub. I had to drive it out with a punch. The only other problem I had was after getting everything back together the new tub seal leaked. When I installed it if fit very loose on the OD. I ordered a new seal hoping it would fit tighter but it didn't so I coated the the seat of the tub and the OD of the seal with gasket shellac. That solved the problem. Working great.

1.Pulled the agitator out. Unscrewed the top nut, which was a little tricky to break loose since it had been in place for over 10 years. Pulled out the entire washing cylinder to unscrew and replace the hub. Not bad but you need to take out the inner tub and that requires doing a little extra unscrewing and prying.