Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Compactor draw was not opening fully as the wheel bearings had seized
I followed the you tube video instructions provided by customer care. This involved pulling the unit free from the cabinet, removing several screws that held the housing in place, this gave access to the wheel assembly, then I removed the nuts that held the wheel assembly in place. Fitting the new wheel assemblies was easy as was replacing the housing screws. After reinserting the draw and pushing the unit back into the cabinet it worked like new
Trash Compactor ram will not move while motor running, stripped power nuts
Move the unit out of the cabinet, and take off the top cover.The two drive screws are easy to see. unscrew the two screws of one of the power nut covers and remove that cover. With pliers, unscrew the plastic power nut from that screw. Screw on the replacement power nut with the help of pliers and some heavy grease. install the bearing cap. Use the same procedure for replacing the plastic power nut on the other screw. To make sure the piston is level, place the cover on the power screw but do not attach it. Measure from the end of the screw to the top of the cover of the first screw, then adjust the second power nut up or down so the two power screw nut covers are the same distance down from the top of the it's power screw Lift up the piton assembly to close the gap, if any (I used a short piece of rope) , and install the screws on the second power bearing cap. After installation. recheck the distance from the top of the power screws to the power bearing caps is close to the same distance so the piston will be level.. This same procedure could be followed for other brands. Power of the appliance and verify functionality, if OK replace the top cover and push unit back into the cabinet..
My very old trash compactor's carrier bag wore out
This new one from part select I think fit better than the original so all I had to do was install the handles as the depiction on the packaging showed and install it. Less than 1 minute.
Rotary switch had finally worn out and was brittle and broken on our 30 plus year old trash compactor.
Removed the switch knob, the outer nut, and the front plate. Unplugged the old switch from the 3 wires and plugged them into the new switch and put it back together with the new knob. Probably less than 5 minutes.
Upon the receipt of my part it just had to be slipped into place. I had the part I needed within 3 days of ordering. My had ordered parts for various items in the past and we have always been very satisfied with the care and experteis of this company.
The plastic power nut had stripped out on my 12 year old trash compactor. Ordered 2 new ones from Partselect and installed them. Now it works like new again.
It is held on with three screws. The PartSelect was the only web site that showed me a picture of the part I wanted. The other web sites said it was no longer made. It was shipped out the day I ordered it, and took a minute to install it. Will order again from your company - great service - thanks.
a plastic bag got caught around the screw and the flange on the nut broke so it couldn,t raise one side so the door was jamed at an angle
I pulled the unit out and tipped it over . I pulled the pan off the bottom then i could put a box end wrench on the screw that was jamed then tuned the screw to loosen the door . i then removed the plastic bag that was wrapped around the screw and put the new nut on and all fixed
Remove the compactor drawer. Remove the front cover from the controls. TAKE A PHOTO OF THE WIRING TO THE EXISTING SWITCH! Remove the screw from the side of the switch and pull the switch out from the machine. You have to look very carefully at the switch to see the color labels on each prong of the switch. Attach gray wire to top prong (GR), red wire to middle prong (R) and so forth. Compare your work to the photo you took. Replace the switch, front plate and drawer. IT WORKS. YAY. Warning, my husband is dyslexic and attached the wires in reverse order and the compactor did not run at all. So, be sure you match wire to label.
REMOVE COMPACTOR DRAWER REMOVE SCREWS ON FACE PLATE REMOVE SCREW NUTS ON PART (SOCKET) SAVE HOLDING PLATE WITH SCREW NUTS TAKE PICTURE OF WIRE CONECTIONS (IN CASE OF POOR RECALL USE PLYERS TO PULL CONECTOR OFF OLD SWITCH REVERS INSTALL TOTAL 25 MINUTES