SVE47600BC Jenn-Air Range - Instructions

Turned the circuit breaker to "off"
Unbolted the unit from its cabinet (4 screws - visible when the oven doors are open - secured the unit in its cabinet)
Slid the unit out of the wall about 2 inches
Removed the control panel.
Unbolted the cooling fan assembly
Unplugged the assembly from the wiring harness
Removed the cooling fan from the oven

Plugged in the new cooling fan
Bolted the new fan in place
Replaced the control panel
Slid the unit back into position
Bolted the unit in place
Turned the circuit breaker back on
Tested

No problems - the hardest part was having to reach to the back of the oven from the front.

As the video described I just unscrewed the sensor from inside the oven. Although I couldn't pull the wiring harness through the insulation (the wires were gathered in back with a wire tie) just four screws to loosen the back panel for access to the connection. My wife says it seems to be heating perfectly now.

The problem was easy to find since the board had caught fire and you could tell which board was bad. I had to remove the protecting jacket. Then removed two screws. I disconnected and reconnected the wires one at a time so I could tell where they went.
The hardest part was pulling the stove out and cleaning the dust and split food.

I was told by appliance repairman that sensor and electronic panel were out - so ordered both as PartSelect was less expensive (about 1/2) than service call price. Sensor was in stock and arrived in 2 days, panel was special order from factory.
Replaced the sensor. Pressed Control Lock pad for several seconds and oven clock came on. Was able to set baking temp, broiler, and convection operation as normal.
Canceled order on panel as Sensor fixed my problem.

replaced broiler element - still would not heat.
Called repairman and the control panel is out and will cost around 200.00 to replace. To replace the element, my son helped as my arms weren't long enough. Removed two screws at back and two screws on front of broiler brace. Pulled out and removed wires and hooked them to the new element. Had to turn off circuit breaker. Pushed element back into the holes and replaced screws.
In this instance, it would have been cheaper had I just called the repairman first. However, I have an extra broiler element in case it goes out again.

Diagnosis is the important aspect. Ovens have plunger-type switches to tell the "brain" door is closed, both for the light AND to allow initiation of self cleaning. Finally discovered one of those switches was "scratchy" in operation and unreliable in closing the circuit. (Push the plungers in and out several times and observe the light.) If not 100% reliable, replace that switch (cheap and easy with a Phillips screwdriver.) Initial guess was a $major "brain"-electronics problem but it was merely a sticky switch. Strange since the unit is about a year and a half old and rarely used. Found the part easily with PartSelect, and it came via UPS quickly.

SHUT OFF BREAKER FOR OVEN! pulled oven out to get at backside,removed 3 screws on back coverplate,removed 2 screws inside oven at sensor in top left corner of oven,disconnected plastic clip at back ,pulled old sensor through hole.replaced sensor with new in reverse order. 15minutes tops.

I took out the side of the cooktop that did not work. I had to take off the bottom of the cooktop and checked where electricity was going and not going. Once I found the part that needed replacing, I went on the website, search for Jen-Air cooktops and model number. From the sketch on the website, I was able to order the part needed. I decided to get 2 in order to replace both parts at one time, just in case. The part arrived quickly and was easy to install. The most time I spent was taking the backside off the cooktop and cleaning it.

The F7 code meant that a button was stuck. I removed the 4 front panel knobs then removed the 8 screws that held the stovetop controllers. Then I carefully removed the ribbon cable from the display assembly. I then reassembled the in reverse order on the new part.

Purchased 2 piece broiler pan from this site

I screwed the light lens into the socket and went beautifully. Better than the original. (I am a retired, 75 yr. old woman).

Stove is over 16 years old. I am getting new kitchen in the summer, did not want to buy another stove! I looked on line and found how easy it was to replace element. We turned off power as suggested and removed element to make sure it matched the one on line. I ordered element on Sunday afternoon and it arrived Tuesday afternoon, FedEx ground. Insert the clips and a couple screws and we were having oven fries for dinner. I could not be happier and pretty darn proud of myself for saving a couple hundred dollars on a repair man!

Removed 4 screws holding trim panel in place. Removed 4 screws on underside of clock panel

Pulled panel out slightly and disconnected the 2 electrical strips

Removed 2 screws holding clock assembly

Disconnected the ribbon circuit tape-push down on the holder tabs and simultaneously pull up gently on trhe ribbon.

Connect ribbon to new unit. Screw unit to panel.
Reconnect electrical strips and reinstall in reverse of disassembly.

Very easy to accomplish

The first thing I did was to turn off all of the power to the range. Then, I removed all of the screws and unhooked the front panel from the range. Then, I rolled the front panel upside down to get access to the wires. I then proceeded to disconnect all of the wires. After that, I removed the circuit board from the panel. Obviously, I just had to reverse the procedure to install the new circuit board. It was one of the easiest jobs I have had to do.

We turned off the stove at the breaker panel. Took off the front top panel of stove and replaced the replacement board. It had three attachments to plug in. We then replaced front panel and turned on the breaker. The stove worked perfectly. It is very nice to have a clock and temperature reading visable again. Part Select was very easy to order from and we received our part within a couple of days. Will certainly suggest them to friends and will use them again.