Quick Question!

Have you ever purchased from PartSelect.com before?

Models > SVE47600BC

SVE47600BC Jenn-Air Range - Overview

Get Parts and Repair Help for SVE47600BC

If you know the range repair part you need, you can browse the list of all parts on the SVE47600BC, or you can search by name or part description. You can also find your part by where it is located on the SVE47600BC by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for SVE47600BC parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.80

Light Bulb - 40W

This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these repla...

$11.48

Grease Filter

This filter is made of metal and is intended for use with ranges and cooktops. Grease filters are an important but often neglected part of ranges. If the filter is full, your extractor fan will become nosier, and cause a bad odor to come from your range. Neglecting the grease filter can also pose a fire hazard in your kitchen. Regular maintenance and cleaning of the grease filter is important and will make the part work more efficiently and last longer. It takes about 30 seconds to replace your grease filter. While replacing the filter, take a minute to check for a grease buildup underneath, and clean out any drip-through grease. As per the manufacturer, if this filter is 1/2" less wide than the original, it will still function the same.

$29.74

Long Oven Sensor

This long oven sensor is also commonly known as a temperature sensor. It is designed for use with ovens and ranges. It is similar to a thermostat; it measures and regulates the int...

$2.96

Screw

This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch. It has 6 threads. Refer to the manual provided by the manufacturer for further information on repair and accurate guidance. Remember to wear work gloves as a safety precaution.

$6.36

Single Door Strike

This door strike is less than an inch long. It is all white in color and it is made entirely of plastic. The door strike fits on the inside of your range and is the locking mechani...

$23.78

2 Piece Broiler Pan

This is cookware designed for use in your range or oven. It is a two-piece dish that is used to grill or cook food while the broil function is on, meaning it can withstand high temperatures. This set includes both the pan and the grid. The grid is the top part. The slotted design allows grease to easily drip into to the pan below. Not only does it catch all of the drippings, it also prevents splatter and smoke while cooking. The pan can also be used separately for baking and roasting. This cookware features a durable porcelain finish, which means it is incredibly easy to clean, and is dishwasher safe. It is roughly 1.5 inches deep, and measures approximately 16.5 inches by 12.5 inches. If your two-piece broil plan is lost, rusted, or damaged this is the replacement you need.

$60.41

Infinite Switch - 240V

This part is used for the 6" and 8" burners. Note: This part has been updated by the manufacturer. It may differ in appearance but will still function the same.

$50.49

Bake Element - 240V

The element has male terminals. This bake element is found on the bottom of the oven.

$6.17

Cartridge Male Contact Spade

This cartridge assembly male contact spade is made of metal. These are sold individually, though each range uses four contact spades.

$48.18

SEAL- DOOR

This oven door gasket prevents heat from escaping the oven cavity when in use. This is a very easy repair that should only take a few minutes. The door gasket may damage or rip over time due to repeated use. If you notice that hot air is escaping from your oven, it is likely that the gasket needs to be replaced. You will need to open the oven door and remove the old seal by pulling it out of place with your hands. The old gasket will be secured with clips that will come out when you pull the entire piece out. The new gasket will have hooks all along the rim, which will line up with the oven door. Simply line up the hooks and push into place outlining the door of the inside of the oven. No tools required.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Replace Grease Filter

  • Customer: Gene from Washington C.H., OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 515 of 521 people found this instruction helpful
Just a couple of minutes to left off the cover grid, left out the old filter and drop in the new one. read more

Oven not holding 350 F, when cooling the coils did not reheat

  • Customer: David from Westford, MA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 122 of 141 people found this instruction helpful
Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening, reinstall 2 screws. ... read more

Burner had one temperature--hot, regardless of setting

  • Customer: James H from Oxford, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 80 of 88 people found this instruction helpful
1. Killed power and removed the regulator's knob, noted the position of the old control.
2. Took off the cover for the center vent and loosened the two screw holding the housing in place--the screws didn't have to come out completely as it is a U-shaped friction hold.
3. Unscrewed the two screws holding the old control switch in place--lifted the h... read more