SRA22B Maytag Refrigerator - Instructions

1. Removed ice bin.
2. Removed vertical panel next to ice bin by sliding two top supports off of support posts and pulling the panel out and up.
3. Removed screw on left side holding ice enclosure in place.
4. Pull ice enclosure out about six inches and tip back end down exposing electrical connector.
5. Detach the electrical connector by pressing the release tabs on the top and bottom of the connector.
6. Removed ice eclosure by pulling it up and out.
7. Detached motor (4 screws) and relay (4 screws) from plastic enclosure. Make sure to keep track of screw positions since they are not all the same size. Use same positions to reassemble.
8. Hold shaft of motor with needle nose vise grips and remove the "U" shaped end piece by turning it clockwise. A sharp rap with a screwdriver handle breaks it loose. Pay attention to the orientation of the washer under the "U" shaped piece (the raised inner edge next to the shaft goes against the "U" shaped piece.
9. Attach the motor and relay to the new ice enclosure paying attention to the screw position.
10. Put the washer on the motor shaft (raised side up) and screw on "U" shaped piece (counter-clockwise).
11. The rest of the installation is a reversal of the removal process.

Pull out fridge and unplug
Remove drip tray from dispenseer
Unscrew face plate (star bit) 2 screws
Carefully disconnect wire strap from faceplate controls
Unscrew dispenser from chute - 3 screws and one is hddend next to actuator.
Carefully disconnect another wire strap to remove unit.
Remove actuator pad
Remove limit switch (i small philips screw)
Replace switch & pad
Re-assemble

Neither the actuator pad nor the limit switch appeared broken or worn but it appears to have solved the problem.

Not a terribly complicaed repair but you need to take care not to damage anything as you take apart. More work than just changing a filter or bulb.

I unplugged the fridge. Loosened the 2 top screws on the ice maker and removed the lower screw. I disconnected the wiring harness and removed the Ice maker. I removed the plastic timer cover in front. I then loosened the screws on the face of the ice maker and removed the broken ice stripper and replaced it with a new one. Re-tightened the screws on the face, installed the timer cover, plugged in the wiring harness, re-attached the ice maker. Plugged the fridge back in and walla, it was making ice in 30 minutes!

I had to cut off the old yoke since the threads had stripped and it would not come off. Once I did that all I had to do was to remove 4 screws on the auger motor and replace it with the new auger motor. Then I put the yoke on the new auger motor shaft and then put the unit back in the freezer. Work time was less than 15 minutes with no problems.

I called the local Amana repair man, wanted $150 for a new ice maker because they could not get the part I needed. Found Partsselect.com and the part cost $17 with shipping. They saved me over $100. The repair was very easy too, just removed a couple of screws.

Thanks,
Matt

From the beginning I have never had good water flow in the door and ice cubes turned out funky. I tried replacing the filter once with hardly noticeable change. The change I did see was $35 less in my pocket. So I bought a filter bypass plug and it now works like a champ. I have well water so I trust its quality and I am very satisfied. I would describe how I did the repair but if you don't no how to change out the filter you probably shouldn't be trying it.

first i remove the two screws like the guy said on your web site. then i pulled the cover off with a upward motion revealing three more screws witch i removed. I then removed the dispencer. unpluged the wires and removed the switch and pad and replaced with new parts.I reinstalled the wires then the unit, installed the screws and cover.Checked for proper operation.Then enjoyed that cold beer! Thanks to your wed site and repair info. I saved at least 100 buck to the repair man. Thanks Partselect.com

I removed all contents from the lower shelf. I, then removed both of the pull out drawers. Secondly, I removed the lower glass shelf and the glass support tray. At this point all four plastic shelf supports were accessible. I removed the inner screw from all four supports and replaced with four new shelf supports. Then reassembled in reverse order. Very easy to do!

Took a putty knife and
Removed the old switch removed the spade terminals from the old switch and replaced them on the new switch and just pushed the new switch back in place

First I removed the spill tray, and removed the two screws on the bottom of the dispenser. I was then able to remove the front of the dispenser, which revealed 3 more screws. After removing those screws, the entire assembly lifts out. I removed the old pad, put the replacement pad on, replaced all the screws and the tray, and was done! It took about 10 minutes, start to finish. I saved at least $75 on the repair by doing it myself, and the part only took 3 days to arrive. Best of all, the water and ice dispenser works like new! Thanks, PartSelect!

I Removed the two wires from the old relay. I Then pulled the old relay off the compressor. Next, I had to get the overload seperated from the old burnt relay, which took some care not to break. The old relay and overload is in a plastic compartment. Then I followed the directions that came with the new relay. The only confusion came with getting the two wires back onto the terminals of the new relay, mainly because the old relay was burnt so badly I didn't have any idea how it was originally wired. I crossed the two wires on the terminals of the relay. The compressor would click off and on, but would not start blowing cold air. I swapped the wires on the terminals and it started working immediately.

Upon careful inspection, I found that the dispenser also would occasionally fail to shut off when dispensing whole or crushed ice, which led me to think that the problem was in the dispenser actuator rather than in the water solenoid or fountain switch control board. To inspect the actuator mechanism, I shut off power to the refrigerator, removed the escutcheon mounting screws, the escutcheon, the cable from the fountain switch control board, and finally the fountain bracket assembly. There was a small amount of hard water scale on the back of the actuator pad, but no groove in the plastic part of the pad that actuates the switch. I replaced the pad and switch (1 screw) and reassembled the dispenser. The dispenser no longer sticks and shuts off normally.

followed the instructions provided and that's it!

Very simple. Matched female plugs with respective male color coded prong; pushed together then inserted unit in slot of freezer sidewall and rotated into position...job done.

Received the union I ordered, then discovered that the tubes were different sizes, so I had the wrong part. I had read elsewhere that it was necessary to trim the two ends of the tubes with a box cutter to stop the leaks - I did this, and the leaking stopped. I was then able to go to a local hardware store and get a 5/16 to 1/4 union and replace it. The leaking is stopped, and the water supply in the door is now working like new. No problem with partselect, but I did buy a caliper so that I can check tube diameters if I ever have a similar problem! This is a great site to find instructions - well worth the time to search!